Home > Hp Psc > Hp Psc 2410 Clicking Noise

Hp Psc 2410 Clicking Noise

Contents

However, I made an inadvertent mistake and pressed the * and # keys. Basic & full are both v4.2.0. btw my fax NEVER worked. [emailprotected] by unknown on Jul 2, 2007 at 9:34am Add comment Please sign in to comment 0 Well it did it again - on start-up it HELP....

Cleaned underside of scanner glass.... It really Works!!!!! Sure need it fixed promptly. Worked for me.

Hp Psc 2410 Clicking Noise

In the end I sent an email to our Solicitors, after having spoken to them previously and advised them to ignore it, listing the catalogue of issues and asking them to The ribbon cord is like a 1/2 inch piece of ribbon - really thin, with lots of wire running through it, and there are several white plugs the ribbon cords plug any idea how to reconnect the encoder strip? by unknown on Jun 8, 2011 at 10:46am Add comment Please sign in to comment 0 I cleaned the glass and it seems to be working.

Working... Staples tried to have nothing to do with it (this was before I knew of the 6yr warranty). This is seriously irritating. Hp Psc 2410 Scanner Stuck The printer is now working.

I tried moving the scanner head to the middle and other end. Hp 2410 Photosmart Printer Troubleshooting Don't forget that the belt has to be clipped into it or it can't move on the rail. to no avail. http://www.pctechbytes.com/forums/index.php?/topic/5991-hp-2410-printer-error-cycle-power/ If you are using Windows XP or 2000 you must download the driver.

Once you have that you can just lift the cover and start looking for the screws holding the cover. There are 5 screws holding the top down 2 on the left are easy .One is under the scan cover lid and 2 more under the right control pannel which comes When I turn it on it makes the same repeatative noise over and over again and then after a minute it goes off but the hourglass is still on the screen Your instructions are great.I was about to just go out and buy a new printer, and thought “what the heck” if I take it apart and can’t get it back together

Hp 2410 Photosmart Printer Troubleshooting

I tried your instructions along with anonymous' advice to pull the control panel forward then up and also cleaned the cables inside the printer. However, when leaving the room, I turned the light switches off, and that turned the power off to the unit, and when I turned the light switch on, the unit came Hp Psc 2410 Clicking Noise Lubricate the carriage bar all the way with Lubriplate Aero (do not use silicon based lubricants).6. How To Reset Hp Psc 2410 Photosmart All-in-one Printer how to solve lol forcifer Printer Support 1 03-08-2006 07:00 PM Posting Rules You may not post new threads You may not post replies You may not post attachments You may

by unknown on Nov 2, 2012 at 9:33pm Add comment Please sign in to comment 0 I tried everything on this forum a while back to correct this same problem. So I figure the electronics still work, just the carriage does still not move. thank you. This works for me too. Hp Psc 2410, Reset

If so go to this web page for setup instructions.http://h10025.www1.hp.comIf you are running XP and don't have the software install disk go to this web page to download or purchase the My 2410 exhibited the same symptoms and I tried everything posted to no avail. But - the good news is, it does respond! I have a month until school I need help NOW!!!

Took it apart and cleaned it, and lubricated the scanner carriage shaft and moved carriage to half way point as suggested and started back up but this also didn't work. You are not liable for the repair costs - have a look on the TS website or speak to them if you get another problem. Once it gets back it keeps trying to go back even though it is at the end of its travel.

The dimensions are 8.7”(Height)x18.2”(Width)x14.6(Depth), and its weight slightly exceeds 18lbs.

by Anonymous on Aug 24, 2008 at 9:35am Add comment Please sign in to comment 0 Here is hoping that the problem is resolved. by Anonymous on Aug 8, 2008 at 8:12pm Add comment Please sign in to comment 0 I had the annoying clicking sound with the hour glass problem too.Just like everyone else,I by unknown on Nov 2, 2012 at 10:40pm Add comment Please sign in to comment 0 Scanner clicking on startup after power outage. Some models are not available in stores or certain countries.

by unknown on Jul 24, 2007 at 6:17pm Add comment Please sign in to comment 0 I just got one of these printers (2410xi)for free--because of the same problem--hourglass just sit's Any help would be appreciated because I don`t want to buy a new printer. you may be able to see you problem right there without going through all what is described.great journey anyway and again cheers and tx to don. - Anonymous Hi Don,Your instructions BestThomas Zahreddinhttp://voicehero.net by unknown on Jan 12, 2009 at 7:36am Add comment Please sign in to comment Many, many thanks for this solution.

Advertisement Autoplay When autoplay is enabled, a suggested video will automatically play next. Using the small blade screwdriver as necessary, remove the bezel on the control panel.5. I dread getting the prompt that I'm running low on ink because it takes me hours to get the old cartridges out. There was no way of forcing it as far to the back as for the carriage to be able slide.

Hope this might work for some of you." These instructions were the fix for me.THANKS! - designair 0 I just got one of these printers (1024xi)for free--because of the same problem--hourglass On both of my computers and using my 2410 all in one I have the same problem. After you remove the cover, flip it over.