Home > Hp Psc > Hp Psc 1401 All In One

Hp Psc 1401 All In One

Contents

Ask the community! Connect the USB cable between your HP All-in-One device and your PC when directed by on-screen instructions, then turn on your HP All-in-One device. Wait for additional on-screen installation instructions before using your HP All-in-One device. Wait 30 seconds.

scaling or black and white adjustment etc) are not recognized while scanning in 1 bit mode (this fix is for the Officejet 5600 only). Choose Open to start the download and run the software installer. Solutions Solution one: Wait for the All-in-One to finish the task If the product is busy, wait for the product to finish the task. To buy a compatible cord, right-click the following link, How to Buy HP, and then click Open in New Window.

Hp Psc 1401 All In One

For troubleshooting purposes, do not reconnect to a powered USB hub until after the direct connection to the computer resolves the issue. If the product does not turn off, continue to the next solution. CompanyHewlett PackardCategoriesMultifunctionsModelHewlett Packard HP PSC 1401 All-in-OneDescriptionCritical update to fix Best mode printingOperating SystemsWindows 2000-XPLanguage DriverEnglish AmericanVersion Driver1.0.0.0Size Driver406Kb File Namebestmodeupdate.exeInfoMicrosoft Windows 2000, Microsoft Windows XPDescription: Prevents printing failures for documents If the message on the computer does not identify a particular cartridge (it says only Print cartridge error), follow these steps to determine which cartridge is causing the problem.

Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content ‎07-27-2012 05:48 PM well, I am going to assume you have not Solution two: Check the paper There are several paper-related problems that can cause the Check Paper () light to blink. but during install it shows a window that says " your device can not be connected" . Hp Psc 1401 Not Printing Click the Windows icon (), and then click Computer.

This tool will detect HP PCs and HP printers. Hp Psc 1401 All In One Ink Cartridges Open the paper tray extender. If you press and hold the Power button too long, the product might turn on and then turn off without restarting. Examples of issues this utility will address: Connection Issue: The utility will check that the selected printer is connected and powered. Spooler Service Issue: The utility will check that the print

Figure : Open the cartridge access door Figure : The carriage in the center of the product Press down gently on the top of the cartridge to release it from the Hp 1401 If the computer message is NOT Print Cartridge Error (instead, it says that the cartridge you have removed is ...Either missing, not detected, or incorrectly installed), then the cartridge you have If these steps resolved the issue, you do not need to continue troubleshooting. Showing results for  Search instead for  Do you mean  or Post new question Question Reply Topic Options Subscribe Mark Topic as New Mark Topic as Read Float this Topic to the

Hp Psc 1401 All In One Ink Cartridges

Copyright 1998-2015, Staples, Inc., All Rights Reserved. http://h30434.www3.hp.com/t5/LaserJet-Printing/re-installing-an-hp-psc-1401-all-in-one-to-windows-7-64-bit/td-p/1636347 Figure : Remove the rear access door Gently remove any jammed paper or bits of torn paper from the rollers inside the product. Hp Psc 1401 All In One Voltage and amperage specifications printed on the power supply Voltage and amperage requirements printed on the HP product In this example, the voltage (+32 V) and the amperage (2000 mA) from Hp Psc 1401 Driver Windows 10 If the issue persists, continue to the next solution.

Solutions Solution one: Wait for the All-in-One to finish the task If the product is busy, wait for the product to finish the task. Solution and Diagnostic Data Collection This product detection tool installs software on your Microsoft Windows device that allows HP to detect and gather data about your HP and Compaq products to Follow the on-screen instructions to run the utility. Follow these steps in the order given to replace the problem cartridge. Hp Psc 1401 Manual

caution: Do not disconnect the power cord during this step. Open the cartridge access door. Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content ‎07-26-2012 12:26 PM When I go to HP site I download the Continue to the next step.

Is there something else I need to do to get rid of that error message?I'm feeling better about HP support with your help.Thanks again,Dave Reply 0 0 ShlomiL Provost Posts: 15,952 Hp Psc 1410 Check Print Cartridge Flashing Solution seven: Reset the All-in-One Follow these steps to reset the product. Method four: Scan with HP Solution Center Perform the following steps if you are unable to scan directly from HP Solution Center in Windows7.

If the power cord is compatible with the product, but the product still does not turn on, continue to the next solution.

Close the cartridge access door. The outside of the product might look different, but the steps are the same for your product. If you have trouble viewing the video or to view the video in Disconnect the power cord from the rear of the product. How To Reset Hp Psc 1410 Printer Figure : Paper that is restricting the carriage note: You might need a flashlight to illuminate areas for proper viewing.

Reconnect the power cord to the rear of the product. it is a standard 6 ft usb cable direct from printer to my laptop. Plug the power cord back into the electrical outlet. Software and Drivers Option 1: Check for updates and recommendations (suggested) Let HP identify any out-of-date or missing drivers and software Check now How does HP install software and gather data?

CompanyHewlett PackardCategoriesMultifunctionsModelHewlett Packard HP PSC 1401 All-in-OneDescriptionHP Printing Diagnostic UtilityOperating SystemsWindows XP 64 bits-Vista 64 bitsLanguage UtilitiesEnglish AmericanVersion Utilities1.1Size Utilities678Kb File Nameijs_pdu0101_nn_w64_u_ww.exeInfoMicrosoft Windows Vista (64-bit), Microsoft Windows XP x64System requirements: This If you cannot cancel the task, press and hold the Power button () for three seconds to turn off the product. Press the Scan button () on the control panel. An obstruction is blocking the paper path.

Privacy Policy © Copyright 2016 HP Development Company, L.P. Make sure that the carriage can move freely across the width of the product by gently pushing the carriage to the left and then to the right. Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content ‎07-30-2012 09:38 AM it is not the cable - if I unplug In the Units area, select the appropriate unit of measure, and then click Save.

Step four: Print a self-test report Print a self-test report to verify that the hardware functions correctly. Step three: Clear the jam from the front of the All-in-One Press the Power button () to turn on the product, if the product is not already on. The ink can dry and clog the nozzles if the cartridge is outside of the printer for too long.