Hp Psc 1400 Cartridge Error
Load the paper into the paper tray; do not push the paper past the rear of the tray. If these steps resolved the issue, you do not need to continue troubleshooting. The print margin specifications can be found in the User's Guide. Consider bookmarking this page on your Web browser, so that you can reference it after restarting the computer. Check This Out
Press and hold the Cancel () button, and then press the Start Copy Color () button. Press, and then quickly release the Power button () to start a power on/off cycle. Solution two: Cancel the task Press the Cancel button () on the control panel. Dip a clean swab in the water and squeeze it to remove most of the moisture. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-c00461967
Is the scanner lamp light on? Plug of power adapter End of power cord into power adapter Electrical outlet Step 2 Turn the product on by pressing the On/Resume button on the front panel and the unit The status lights on the right hand of this button indicates which setting is active.
The carriage moves into the middle of the access area. Issue: The Power, Check Paper, and Check Cartridge lights are blinking In this error condition, the following control panel light pattern displays: Power light: Blinking Check Paper light: Blinking Check Cartridge When the On light is flashing, release the On and Paper Size buttons. Disconnect the power cord from the rear of the product.
Step 4: Clean the problem cartridge contacts If the light is still blinking, clean the electrical contacts by the procedure below: Gather the following items to clean the cartridge and print Open the cartridge access door in the front of the unit. Is there a paper jam? http://support.hp.com/in-en/document/c00665699 If the product has not been set up before, ensure correct installation of the control panel overlay by following the instructions.
The carriage moves into the middle of the access area, unless there is an obstruction. Pull out any jammed paper or any other foreign material that could not be removed from the rear access door. Visit http://www.suresupply.com.Learn what to do if an HP Officejet J4680 All-in-One Printer displays either an "Incompatible Print Cartridge," "Cartridge Problem," or "Cartridge Missing or Damaged" error message. WARNING: Make sure that the power cord is disconnected from the product to avoid an electrical shock.
Method three: Scan with HP Solution Center Perform the following steps if you are unable to scan directly from HP Solution Center in Windows Vista. Very helpful Somewhat helpful Not helpful End of contentUnited StatesHP WorldwideStart of Country / Region Selector contentSelect Your Country/Region and LanguageClick or use the tab key to select your countryArgentinaAustraliaBelgiqueBoliviaBrasilCanadaCanada-françaisČeská republikaChileColombiaDeutschlandEcuadorEspañaFranceIndiaIrelandItaliaMagyarországMéxicoNew Disconnect the power cord from the rear of the product. Solution three: Service the All-in-One If you have completed all the steps and are still experiencing a problem, continue to the Service the All-in-One section at the end of this document.
The swab should be only slightly damp. his comment is here Was the information on this page helpful? Step 2 Check the power connections: Make sure that the unit is connected straight to the electrical outlet without any other device or power strip and surge suppressor between the electrical Double-click Digital Imaging.
Double-click Digital Imaging. Moose Scrapper 713,354 views 4:30 HP Print Cartridge(s) Missing or Not Detected Fix - Duration: 1:19. Clean the scanner glass. http://permamatrix.net/hp-psc/hp-psc-750-cartridge-error.html Video of replacing cartridges The following video demonstrates the steps explained on this page.
The video contains no audio.If you have trouble viewing the video or to view the video in a different size, view the video on YouTube. If service is not required, the steps in this document will assist in solving some common product issues. Do not use paper that is too thin, too thick, or too glossy for the product.
From the What do you want the computer to do?
The Photo paper setting produces copies in Best quality. 8: Start Black Copy Starts a black-and-white copy 9: Start Color Copy Starts a color copy 10: Scan Starts a scan from Wait until the Power light () stops blinking. Unplug the power cord from the unit. Right-click the following link, How to Buy HP , to buy a compatible power cord.
NOTE: Before you begin, make sure that the product is connected to your computer. Try the steps below to identify the problem cartridge: Open the cartridge access door. Ask a Question Usually answered in minutes! http://permamatrix.net/hp-psc/hp-psc-750-black-cartridge-error.html Avoid touching the nozzles.
Close the rear door. Solution one: Make sure that the All-in-One is plugged in Follow these steps to make sure that the power cord is connected to the rear of the product and plugged into Solutions Solution one: Wait for the All-in-One to finish the task If the product is busy, wait for the product to finish the task. Step 8 Try printing again.
If both part numbers do not match and your product is still under warranty, please Contact HP . Figure 5: Replacing the cartridge The black or photo cartridge goes on the right.