Home > Hp Psc > Hp Psc 1350 Error Blinking Lights

Hp Psc 1350 Error Blinking Lights

Click on this and a box will open letting you choose how to scan, where to save it ect. Make sure the HP product supports the paper type. I tried getting a new 56 cartridge; removing and cleaning the cartridges and printer cartridge terminals with alcohol; doing a full resent. Modify your browser's settings to allow Javascript to execute. Check This Out

Click OK to accept the settings. Solution two: Make sure that the front panel overlay is installed correctly If the front panel overlay, or bezel, is incorrectly installed, the product may indicate a false carriage stall error Figure : Open the cartridge access door Figure : The carriage in the center of the product Disconnect the power cord from the rear of the product. I have just installed 56 black cartridge, do you think 57 color cartridge is necessary for the printer to copy or print the document? look at this web-site

With the power on, disconnect the power cord from the rear of the product. Reach inside the product through the cartridge access door, and then manually move the carriage. Dip a swab in the clean water, and then squeeze it to remove most of the moisture.

Anmelden Teilen Mehr Melden Möchtest du dieses Video melden? Place the cartridge in its slot at a slight upward angle, and then press up and forward until the cartridge snaps into position. Press the On/Resume button () to turn on the product. The alignment page prints.

The color test page comes out with colors that are not yellow,magenta and cyan. Wait ten minutes to allow the cartridge to dry, then reinstall the cartridge, plug the printer back in, and close the cartridge access door. Printer makes noise as if printing but paper has nothing on it. If the issue persists, continue to the next solution.

Click OK to accept the settings. If the issue persists, continue to the next solution. Solution two: Test the power with a compatible power cord from a different product If you have another available power cord that is compatible with the product, use the alternate cord Step two: Test the connection Press the appropriate button(s) on the product again to perform the intended task.

Unplug the power cord from any power strips or surge suppressors. this contact form note: Try to clean the contacts quickly enough that the cartridge is not outside of the printer for more than 30 minutes. If the issue persists, continue to the next solution. Do not overload the tray with paper.

It is not hooked up to the computer. his comment is here Figure : Load the alignment page Close the scanner lid while holding the alignment page in place. Ideas or suggestions?Thanks, Juan by unknown on May 30, 2013 at 6:37am Add comment Please sign in to comment Please sign in to comment HP PSC - Printer / Scanner / Reconnect the power cord to the rear of the product.

I think HP has built in obsolescence to sell more printers and ink! Step one: Reset the power module The power module has a safety feature that protects the product during a power surge. You may NOT copy or distribute the content that appears on this site without written permission from Fixya Ltd. © 2005-2015, Fixya, Ltd. this contact form The ink can dry and clog the nozzles if the cartridge is outside of the printer for too long.

Solution three: Make sure that the control panel overlay is installed correctly If the control panel overlay, or bezel, is incorrectly installed, the product might indicate a false carriage stall error If the front panel overlay is already installed, and your printer has been working for some time, do not attempt to reinstall the overlay. If the electrical outlet works, but the product still does not turn on, continue to the next solution.

Contact HP or an electronics store to replace the power cord.

caution: Do not remove jammed paper at this stage. If these steps resolved the issue, you do not need to continue troubleshooting. The Size is: window opens. If these steps resolved the issue, you do not need to continue troubleshooting.

If the issue persists, continue to the next step. Press and hold the Cancel button (), and then press the Start Copy Color button. The swab should only be slightly damp. http://permamatrix.net/hp-psc/hp-psc-1350-check-print-cartridge.html Figure 42: Insert the cartridge Firmly push the cartridge in until it snaps into place.

Step three: Align the cartridges Follow these steps to align the cartridges. I need to remove the cover. Hinzufügen Möchtest du dieses Video später noch einmal ansehen? If these steps resolved the issue, and the test page prints, there is no need to continue troubleshooting.

Solution six: Resolve the cartridge problem Follow the steps in the order given to resolve the cartridge problem. If these steps resolved the issue, you do not need to continue troubleshooting. Figure : Do not touch the contacts Place the cartridge in its slot at a slight upward angle, and then press up and forward until the cartridge snaps into position. The illustration below shows the carriage and the contacts.

everytime i tell the computer to print, the icon appears at the bottom for about 10 seconds and then disappears. Look inside the product to see where the carriage is stuck, and then check for any torn paper or objects that might be restricting the carriage. Reconnect the power cord to the rear of the product. View Most Popular PSC 1350 All-In-One Thermal Printer Printers & Copiers Related Question Hp 1350 does not copy HP PSC 1350 All-In-One Thermal Printer Open Questions: 0 Answers how to activate

If the product operates normally, allow the product to complete the task. Solutions Solution one: Close the cartridge access door Check the cartridge access door to make sure that it is closed completely. I've done everything suggested on the hp site short of having it serviced. Experiencing frequent or recurring paper jams?

I thought I had every tool I would ever need in life, but can't find one that will undo the 4 deep recessed holding screws. If the On/Resume light starts blinking, the tricolor cartridge (the cartridge on the left) is the problem cartridge. If the electrical outlet does not work, plug the product into another outlet that does work. Unplug the power cord from any power strips or surge suppressors.

Gather the following materials: A clean, lint-free cloth, or any cloth that will not come apart or leave fibers Distilled, filtered, or bottled water (tap water might damage the product) Press If the issue persists, continue to the next solution. THANKS!!! Slide the two pins on the right side of the door into the two holes on the right of the product, and then snap the left side into place.