Home > Hp Psc > Hp Psc 1200 Driver

Hp Psc 1200 Driver

Contents

by thtwassick / June 15, 2006 12:27 PM PDT In reply to: HP PSC 1200 Series Scanning Problems Mooneye, tried e-mailing you per your address in your post, but the e-mail Reconnect the USB cable to the rear of the product. Try the intended task again. Please ensure that the scanning device is connected properly and try again". Check This Out

Connect with us facebook twitter CNET Reviews Top Categories CNET 100 Appliances Audio Cameras Cars Desktops Drones Headphones Laptops Networking Phones Printers Smart Home Software Tablets TVs Virtual Reality Wearable Tech Thank you for helping us maintain CNET's great community. The sequence must be completed within ten seconds. If these steps resolved the issue, you do not need to continue troubleshooting. http://www.neowin.net/forum/topic/449372-hp-psc-1200-series-system-error-solution/

Hp Psc 1200 Driver

Right-click this link, Product Support Home Page, and then click Open in New Window. Figure : Disconnect the power cord Wait 15 seconds. Solutions Solution one: Wait for the All-in-One to complete the job Allow the product to complete the job. An obstruction is blocking the paper path.

When the Check Paper and Check Print Cartridge lights begin to blink simultaneously, release both the Cancel button () and the On/Resume button (). I'm really not impressed with WindowsXP though. Step one: Remove any loose paper Remove any loose sheets of paper from the input tray and the output tray. Hp Psc 1200 Driver Windows 7 64 Bit Download If the computer is turned off, press the Power button on the computer to turn it on.

When the lights begin to blink, press and hold both the On/Resume button () and the Paper Size button at the same time. Hold the cartridge by its sides. A sequence of buttons on the control panel must now be pressed in the order presented. The product aligns the cartridges. Figure : Press the Scan button to begin the alignment The alignment is complete when the On/Resume light () stops blinking.

Load plain, white paper into the paper tray. Hp Psc 1200 Printer Offline The carriage moves to the center of the product. I've tried updating drivers, uninstalling/reinstalling time and time again. The carriage moves to the center of the product.

Hp 1350 Printer Check Print Cartridge Error

Post a reply Discussion is locked Flag Permalink You are posting a reply to: HP psc 1200 The posting of advertisements, profanity, or personal attacks is prohibited. The alignment page prints. Hp Psc 1200 Driver Please enter a Product Number to complete the request. Hp Psc 1210 Driver Download Solution two: Cancel and then retry the task Follow these steps to cancel and then retry the current task.

This video shows how to print a test page Click here to see this video in full screen on YouTube. his comment is here Paper jam causes The following factors can cause paper jams: Paper loaded incorrectly in the paper tray. Press the On/Resume button () to turn off the product. If the issue persists, continue to the next solution. Hp Psc 1200 Driver Windows 7

Scroll to the bottom of the page, and then make sure the country/region location is correct. Thank you, really.. As far as I know, HP has no plans to release a new software package for the PSC 1200. this contact form Figure : Check the electrical connections Press the On/Resume button () to turn on the product.

This video shows how to clear a paper jam from the All-in-One Click here to see this video in full screen on YouTube. Hp Psc 1210 Check Print Cartridge Error THANK YOU MANY TIMES OVER. When prompted, you plug in the USB cable.

Solution two: Plug the All-in-One directly into a wall outlet The power source your product is plugged into might not function properly.

Solution six: Clean the paper feed rollers Dust, paper fiber, and other debris might accumulate on the paper feed rollers and cause paper jams and paper feed issues. Connect the alternate power cord to the rear of the product. Solution three: Press the On/Resume button more slowly The product might not respond if you press the On/Resume button () too quickly. Hp Psc 1200 Series Windows 7 I'm suffering the same exact problem with my HP1200PSC.

This page requires Javascript. Although not particularly technical, I can do the basics (as I think of them), like installing, updating drivers, etc. If the issue persists, continue to the next solution. navigate here If you think you have received a fake HP Support message, please report it to us by clicking on the blue “Report Inappropriate Content” button above the message.

Solution five: Check for carriage obstructions Follow these steps to make sure that the carriage can move freely. If the front panel overlay is already installed, and your printer has been working for some time, do not attempt to reinstall the overlay. It was lengthy. Press the On/Resume button () to turn on the product.

Do not print on paper with paper clips or staples attached. HP is either unwilling or unable to update the drivers so that they are working with the constant WinXP updates! Remove any loose paper or obstructions found. The reset is now complete.

Nothing fancy. Press and release the Color Start Copy button. The alignment page prints. Only add paper to the tray when the product is not printing.

Blinking Lights on the HP PSC 1200, 1310, 1340, and 1350 All-in-One Printer Series Blinking Lights The following sections describe all combinations of blinking (flashing) lights displayed on the product control Step four: Print a self-test report Follow these steps to print a self-test report. note: For best results when loading legal-size paper, fold in the paper tray extender before loading the paper to avoid a paper jam. Reconnect the power cord to the rear of the product.

However, after doing the :IF THIS DOES NOT WORK FOR YOU TRY THE DEP PROCEDURE AGAIN BUT ADD ALL VERSIONS OF C:\\WINDOWS\\system32\\spool\\drivers\\w32x86\\3\\hpzeng07.exeSOME ARE IN OTHER FOLDERS OF THE w32x86 directory.I hope Darrell Lewis Flag Permalink Reply This was helpful (0) Collapse - you are not alone- CNET forums | Peripherals forum is: by DarCLew2 / June 16, 2006 6:29 AM PDT In Step three: Align the cartridges Follow these steps to align the cartridges. If the power module does not have an LED, continue to the next step.