Home > Hp Printer > Hp Printer Error 80.x

Hp Printer Error 80.x

May be feed problem. Use the Wireless SetupWizard available from the printer control panel to make a wireless connection. Turn the printer power off, install it in a different EIO slot, and turn the printer power on.5. Replace the Fan. Check This Out

top 13.XX.YY.DUPLEX JOB INTERRUPTED Description There was an error while the printer was duplexing. If the printer is on a network, AUTO CONTINUE should probably be set to ON. Figure 44: Turning power off Unplug the power cord and disconnect any cables. NOTE: Avoid spilling loose toner.

Figure 38: Removing the fuser Remove the jammed paper. Replace the formatter assembly.HP LASER PRINTER 4345MFP, 5025MFP, 5035MFP ERROR 8X.YYYY EIO ERROR1. Check connector J018 on DC Controller and connector at Fan 3. 2.

Reseat the specified DIMM. 2. Is the software set for the size you're using? Turn the printer off, reseat the EIO accessory in slot [z], and then turn the printer on. 3. alternates with 41.3 LOAD TRAY XX: [Type] [SIZE] For help press ?

Press the (Up Arrow) button and the (Down Arrow) button to step through the instructions. I would like to offer my assistance today with resolving this error state. Look for the jam in another location, contact HP, or contact an authorized service provider. Figure 61: Sealing tab on end of print cartridge 1 - Sealing tab bent and removed from end of print cartridge CAUTION: Avoid touching any black toner on the tape.

If the message persists, contact HP Customer Support. The X value refers to the location of the problem: 0 = Internal memory 1 to 4 = DIMM slots 1, 2, 3, or 4 1. Make sure that the paper is neatly stacked and that the paper guides are not too tight against the paper. Turn the device off and then on.3.

The EIO accessory card has encountered a critical error.2. http://h30434.www3.hp.com/t5/DesignJet-Large-Format-Printers-and-Digital-Press/error-code-80-01/td-p/5433302 Replace DC Controller PCA. 3. For embedded print servers, use the SERVICE menu.8. The dual inline memory module (DIMM) that caused the error will not be used.

External fuser access door not closed. 4P/5P Only: 1. http://permamatrix.net/hp-printer/hp-printer-error-100-vsa.html This is typically an e-label issue. Is the paper size correct? Turn the printer off, and then turn the printer on. 2.

Printing can continue, but behave unexpected in response to the changed settings. Check and reinstall. Replace PS1 if defective. 2. this contact form Pull gently on the bin to make sure that the hinge pins are fully inserted.

The media is probably wrapped around the fuser roller. If you cannot connect thecomputer to the network, contact the person who set up your network or the router manufacturer; there mightbe a hardware issue with the router or computer.Restart components alternates with 55.X PRINTER ERROR To continue press (Select) 56.1, 56.2 PRINTER ERROR To continue turn off then on 57.X PRINTER ERROR To continue turn off then on 57.7 DUPLEX FAN

Action Turn the printer off and then on.

If the above action does not solve the issue, contact HP, or contact an authorized service provider. Error 10.32.00 Unauthorized Supply Alternates with for help press "?" - A new non-HP supply has been installed this message continues until you press the check button or install an HP If CLEARABLE WARNINGS is set to JOB in the printer configuration menu, these messages are cleared by the next print job. (Click here to see the description of CLEARABLE WARNINGS under Figure 10: Checking the quality of the inserted paper Slide the tray back into the printer.

These settings set the amount of time that a clearable warning is shown on the printer control panel display. Check RAM expansion card, reseat if necessary. 2. Computer and printer may be set to different baud rates. 2. navigate here For your product the troubleshooting steps for this specific issue can be found here.

Error 23 I/O Not Ready ALL PRINTERS The I/O card is not accepting data. Verify the stacker or stapler/stacker is installed correctly and that its electrical connector is seated in the connector on the printer. This can generally get you 100 or so more pages. Pull outward on the blue staple cartridge to remove it.

Turn the printer off. 6. Replace cable, AC Power Module to DC Controller, connector J208. (P/N RG1-0912-000.) IIP, IIP+, IIIP Only: 1.