Home > Hp Officejet > Hp Officejet Pro 8100 Printer Troubleshooting

Hp Officejet Pro 8100 Printer Troubleshooting

Contents

Open the cartridge access door and the printer lid. Plug the power cord back into the wall outlet. Solutions Important: You must follow these solutions in the order presented to resolve the issue. Test known good component. Source

Full Boot may also be enabled to run every 1 to 30 days on a regularly scheduled basis. Check tabs on side of toner cartridge. Bad registration sensor or bad fuser exit sensor. If the issue persists, continue with the next solution. http://support.hp.com/us-en/document/c02906379

Hp Officejet Pro 8100 Printer Troubleshooting

Power button LED blinks 8 times with 8 beeps BIOS or CMOS problem (ROM) Perform BIOS recovery with external media (USB/CD-ROM). Issue: The Power light is on In this normal condition, the following light pattern displays on the printer control panel: Power light: On ePrint light: On or off Wireless light: On The report prints. note: Make sure that the colored dot on the cartridge label matches the colored dot on the slot.

Video of clearing a paper jam The following video demonstrates how to clear a paper jam. Step one: Remove any loose paper from the trays Figure : Do not pull If the printer does not turn on by itself, press the Power button to turn it on. Step one: Check the cartridge access area with the carriage docked Press the Power button to turn off the printer. Hp Officejet Pro 8100 Reset The report prints.

Replace the power supply. Replace the system board. NOTE: The printer might go through a warm-up period. try here If these steps resolved the issue, and the test page prints, there is no need to continue troubleshooting.

Unplug the power cord from the wall outlet. Hp Officejet Pro 8100 Flashing Wireless Light Retest. Reconnect the power cord to the rear of the printer. If you are experiencing problems with certain paper types or sizes, see the Product Specifications to ensure that your printer supports other sizes and types of paper.

Hp Officejet Pro 8100 Wireless Light Blinking

Sign-in Register Site help Skip to ContentSkip to FooterLaptops & tablets Business Premium Gaming Standard laptops Workstations Convertibles & detachables Tablets 3-in-1 Desktops Business Immersive Gaming Towers Workstations All-in-ones 3-in-1 Printers Check This Out Check Fan 3, replace if necessary. 4000/4050/4100/5000 only: 57.4 Printer Fan 57.7 Duplex Fan 8000/8100 only: 57.2 Fan 3 location: formatter 57.3 Fan 2 location: Low-voltage powersupply 57.5 Fan 1 location: Hp Officejet Pro 8100 Printer Troubleshooting Doing so could cause the printhead or cartridges to be incorrectly seated, which could damage the print mechanism and cause printing problems. Hp Officejet Pro 8100 Ink Lights Blinking Figure : Insert the printhead Carefully lower the latch handle on the carriage to secure the printhead.

Privacy Policy © Copyright 2016 HP Development Company, L.P. this contact form Replace cable, AC Power Module to DC Controller, connector J208. (P/N RG1-0912-000.) IIP, IIP+, IIIP Only: 1. Replace front chassis fan. 515-Power Supply fan not detected Power supply fan is not connected or may have malfunctioned. Repeat these steps to insert the other cartridges. Hp Officejet Pro 8100 Printhead Error

Reconnect the power cord to the rear of the printer. System Board 5.5 The embedded controller rebooted the system after a possible lockup condition had been detected through the use of a System Health Timer, Automated System Recovery Timer, or other After you remove an old cartridge, insert a new cartridge within a few minutes to avoid possible damage to the ink system. have a peek here Remove the new cartridge from its packaging.

Solution Connect the power cord to the printer and to the wall outlet. Hp Officejet Pro 8100 Factory Reset If you completed all the preceding steps and your product still has an issue, you might need further assistance from HP. For one device, use SATA 0.

Z7_3054ICK0KGTE30AQO5O3KA30N0 hp-concentra-wrapper-portlet Actions ${title} Loading...

Pull out tray 2 (if installed), and then remove any loose sheets of paper from the tray. Step two: Print a self-test report Print a self-test report. Turn the printer around so that you can access the rear side. Hp Officejet Pro 8100 Symbols Wait until the warm-up period finishes before you proceed.

Lifting the latch could cause the printhead or cartridges to be incorrectly seated, which could damage the print mechanism and cause printing problems. Figure : Insert the new printhead Carefully lower the latch handle on the carriage to secure the printhead. top Beep and LED code descriptions Beep code tables are provided in the following sections of this document to help you isolate and understand the issue. Check This Out Press the Power button to turn on the printer.

If the issue persists, continue with the next solution. Update BIOS while affected components are removed. A duplicate cartridge is installed. Reset CMOS.

Make sure the memory module(s) are installed properly.