Home > Hp Officejet > Hp Officejet D145 Carriage Error

Hp Officejet D145 Carriage Error

The steps below will clear the error condition, which should solve the problem if it is caused by an incorrect detection of air. Thanks View answers OfficeJet: Clear carriage jam. Disconnect the power cord from the back of the product. Step one: Remove any loose paper Remove any loose paper from the input tray and output tray. have a peek here

Disconnect the USB cable from the back of the product. If these steps resolved the issue, and the test page prints, there is no need to continue troubleshooting. Step two: Checking for paper feed problems and carriage blocks Click here (buu03110) (in English) for more information on paper or carriage jams. Reconnect the USB cable, and then try to print again. http://www.fixyourownprinter.com/posts/23597

Press the Power button () to turn on the product. If any torn pieces of paper remain inside the product, more paper jams are likely to occur. If the test page does not print, continue with the next solution. Trying to clear a paper jam from the front of the product can damage the print mechanism.

See the steps on how to print a self-test report at the top of this document. Jun 28, 2009 | HP OfficeJet 6110 All-In-One InkJet... 1 Answer IDS failure, call HP message comes up Hope this helps you. Solution one: Turn the All-in-One off and on again Follow these steps to turn the product on, and then off again, to reset the print mechanism. Reconnect the power cord to the back of the product.

Hinzufügen Möchtest du dieses Video später noch einmal ansehen? Disconnect the power cord from the back of the product. If there really is air in the manifold, however, this procedure will not solve the problem and the printer will have to be serviced. http://support.hp.com/us-en/document/c00310245 WiedergabelisteWarteschlangeWiedergabelisteWarteschlange Alle entfernenBeenden Wird geladen...

You might also experience the following symptoms: The product won't print. note: If the product prints when plugged directly into a wall outlet, the power strip or surge suppressor might not be allowing enough voltage to reach the product. Open the carriage access door by lifting the handle until the door locks into place. yes, that is a carriage jam and not paper, the grinding is from the clean station that gets blocked with dried ink and cant move.

Complementary Content IBM WebSphere Portal Home IBM Logo Sign Up Log In Welcome Getting Started Contact HP - Anonymous Contact HP Product Context View Support Home Test page Product Home Product

So it sounds like it needs to be serviced which could get expensive. How does HP install software and gather data? Follow these steps to remove and then reinstall the cartridges.

If the carriage is stuck on the left side of the product, move the carriage to the right side of the product. http://permamatrix.net/hp-officejet/hp-officejet-6500-paper-jam-carriage-stuck.html The print job stops unexpectedly. except scanner. Anmelden Statistik 6.521 Aufrufe 2 Dieses Video gefällt dir?

note: Refer back to the steps in this table after attempting each solution. HP OfficeJet Printers &... If the issue persists, continue with the next solution. Check This Out Z7_3054ICK0KGTE30AQO5O3KA3016 hp-feedback-input-portlet Actions ${title} Loading...

Press Enter to align. Does anyone know of any common problems or can give me any idea's on where to start? Beware.

Reconnect the USB cable, and then try to print again.

Press the Power button () to turn on the product. See your browser's documentation for specific instructions. {} Z7_3054ICK0KGTE30AQO5O3KA30U5 hp-support-head-portlet Actions ${title} Loading... Check the scanner (if it has a flatbed) Open the scanner cover. Step one: Remove the cartridges Press the Power button () to turn on the product.

Privacy Policy © Copyright 2016 HP Development Company, L.P. View answers IBM Selectric II carriage return stuck My IBM Selectric II typewriter fails to return the carriage when either the Return or Exp key is pressed. Solution three: Make sure that the carriage moves freely Use the following steps to make sure that the carriage moves freely. http://permamatrix.net/hp-officejet/hp-officejet-pro-8500-carriage-jam-error-message.html It will not print.

Solution seven: Service the All-in-One Contacting HP for service in all countries/regions except Asia Pacific. Autoplay Wenn Autoplay aktiviert ist, wird die Wiedergabe automatisch mit einem der aktuellen Videovorschläge fortgesetzt. Repair fees might apply for out-of-warranty products. When power is applied it tries to move but can't also trying to physically move does not work ...

Try to print a self-test report. When I turn it on the error reads "carriage error, close latch, press enter." I have tried taking printheads out, turning off, then turning on, and replacing ... Nothing visible in front carriage path either. If these steps resolved the issue, and the test page prints, there is no need to continue troubleshooting.

Wait until the warm-up period finishes before proceeding. Follow these steps to remove and then reinstall the cartridges. If these steps resolved the issue, and the test page prints, there is no need to continue troubleshooting. Reconnect the power cord to the back of the product.

If the scanner mechanism moves without noise, continue with Step two below. View Most Popular OfficeJet d145 InkJet Printer Printers & Copiers Related Question Non responsive printer HP PSC 2410 All-In-One InkJet Printer Open Questions: 0 Answers Error msg - No color supply I've explained the situation to HP and they just don't ... With the lid open, press the Start Copy button to make a copy.

The system returned: (22) Invalid argument The remote host or network may be down. Press the Power button () to turn on the product.