Home > Hp Laserjet > Hp Laserjet Error 54.2

Hp Laserjet Error 54.2

The control panel will read, Engine Diags Continuous = N.Press ITEM to the right four times. Showing results for  Search instead for  Do you mean  or Post new question Question Reply Topic Options Subscribe Mark Topic as New Mark Topic as Read Float this Topic to the by unknown on Jul 14, 2004 at 3:57pm Add comment Please sign in to comment 0 Well I did have this problem to start with, now my carousel dosent spin so Have power cycled it 4 or 5 times, no help. http://permamatrix.net/hp-laserjet/hp-laserjet-error-10-10-00.html

Are their voltage checks that would pinpoint the trouble? Also, the yellow print cartridge may have stopped at the top of the carousel. A metal plate with part number RB2-0965 etched into it covers the sensor.Performing a sensor test in the Diagnostics Mode will test PS10 for correct operation:NOTE: When running a Diagnostic Mode About Press Copyright Creators Advertise Developers +YouTube Terms Privacy Policy & Safety Send feedback Try something new!

The printer should print out a information data pages and error codes but it never gets past the 54.2 error message. We reset the Format board and the printer is working like champ. Sign in 67 12 Don't like this video? Then kicked the sides a few times and it worked.

I have the left side of the printer cover removed. have tried all of the above. I then vacuumed out all the toner inside the printer. I expecially cleaned the hard toner off the carousel drive gears as you suggesed.

Thanks! It is part of the carousel drive assembly. Uploaded on Sep 13, 2011Shows how to re-index the carousel on an HP LaserJet 2840 AIO. *RAW VIDEO* Sorry for the poor camera work, best I could do on short notice navigate here I would be most appreciative if you could send me or email or direct me to the pictures you refer to in the troubleshooting check list you shared with us.

Sign in to make your opinion count. Thank you! Register · Log In HP Support Forum Home > Printers > Inkjet > HP Color Laser Jet 2840 AIO Printer 54.2 error HP Support Forums Join in Sign in to report inappropriate content. If I do get the error then it's a pain to hafta do the whole warmup routine again.If anyone else knows something else I can try that would be great. -m

Carousel can be knocked out of alignment by cheap aftermarket toners that have binding up gears; gears on new toners should turn by hand easily. http://www.fixyourownprinter.com/posts/20135 Sign in 13 Loading... Which part is the motor for the carousel? Add to Want to watch this again later?

when the break is released, the caroussel rotates, with a push, away from meAs far as cleaning them, I have, but I guess it's a good idea to try again. http://permamatrix.net/hp-laserjet/hp-laserjet-5m-53-12-03-error.html Skip navigation UploadSign inSearch Loading... Clean the sensors with a brush. Cleaned out excess toner tray.

Thank you! Register · Log In HP Support Forum Home > Printers > LaserJet > Re: 54.2 Error on HP MFP M175NW HP Support Forums Join in the conversation. by unknown on Jul 7, 2004 at 3:10pm Add comment Please sign in to comment 0 I have resolved this problem most time by cleaning the gears for carousel drive. DSI Analize 525,824 views 4:15 Loading more suggestions... http://permamatrix.net/hp-laserjet/hp-laserjet-error-19-1.html Up next Toner tauschen HP LaserJet Pro 100 M175nw Teil 01/01 - Duration: 6:42.

But now after putting it back together it will not run off of the network. I tried switching off/on as well as unplugging it but now I am getting a 54.2 error as well as the grinding noise you get with carousel problems. Locate the carousel brake release (Figure 1, call-out 1); press the metal tab with the end of a pen, and hold it down.Rotate the carousel around with another hand until one

I tried your suggestion and after several attempts I got it to work but the left side panel needs to be permanently off.Have you ever found why this piece of plastic

You'll need a small flat blade screwdriver. Did anyone find out where PS 11 is ? by unknown on Jul 3, 2007 at 9:35am Add comment Please sign in to comment 0 Summary is good except :-if I release the brake, I CANNOT trun the caroussel in Loading...

When you disasembled, it simply lost the settings.Good luck in your quest. If the error does not clear with any cartridges installed, and the sensors function properly, the Developing PCB and the carousel may require replacement. Loading... this contact form HP Support Forums Join in the conversation.

For a new be repairing laser printers this forem is great. I disassembled those, washed and used sandpaper to improve the adherence and printer started to work.Hope this information to be useful for someone. To perform the Developer TestPress MENU until Engine Diags Continuous=No is displayed.Press ITEM until Developer Test is displayed.Press SELECT to begin the test.NOTE: Turn the printer off and on again to Newer printers are made for earlier replacement of the expendable kits, ink cartridges, and fusers for profit are they are used up as pages are printed.

The following is a copy and paste of the doc:document number: bpl90005 IntroductionError 54.2 occurs when the carousel of an HP Color LaserJet 4500 or 4550 series printer cannot rotate properly. Is there anymore censors that I can't see that's stopping it and giving me the error? In these cases, the black, plastic lever on the carousel drive assembly was pushed out of its home position (see Figure 4).The toner level sensor assembly is attached to the carousel Sign in to report inappropriate content.

by Anonymous on Jul 25, 2007 at 3:23pm Add comment Please sign in to comment 0 As a continuation of my post directly above, the only common anomaly between the printers All sensors are ok, in diag mode everything runs ok including carusel, all fans are ok... I also oiled the two little clutches on the carousel drive assembly. Close Yeah, keep it Undo Close This video is unavailable.

Let's see what happens. Show more Language: English Content location: United States Restricted Mode: Off History Help Loading... Does the error correspond to the white plastic piece being out of position?-m by unknown on Jul 26, 2007 at 9:28pm Add comment Please sign in to comment 0 When you