Hp Laserjet 5100 Printer Specifications
You will see the status of all the printheads at once. If the message does not clear, go to step 2. 2. Turn the printer off, and then turn the printer back on. 2. If after a recovery the message persists, and the quality of your prints is unacceptable, replace the printhead(s). Source
If the message returns to OK after performing the first step, do not continue. Knowledge Centered Support 2016-04-27|Apr 27, 2016 160 HP 5500 Switch -ARP_DUPLICATE_IPADDR_DETECT Every Time a Client Network Device Moves From One Bridge Aggregation Group to Another Knowledge Centered Support 2016-04-06|Apr 6, 2016 Please wait while we process your request. If the image quality is NOT acceptable: Try using the image quality print. http://h20564.www2.hp.com/portal/site/hpsc/public/psi/troubleshootResults?sp4ts.oid=74341
Hp Laserjet 5100 Printer Specifications
XX21 Replace The printhead has reached a degradation level that prevents the printer producing acceptable image quality consistently. Press [Go] to print the transferred data. (Some data might be lost.) If this message appears often, simplify the print job. MEMORY FULL STORED DATA LOST No memory is available in the printer.
An error occurred in the printer's nonvolatile memory (NVRAM) and one or more printer settings have been reset to the factory default. 1. We tear apart, rebuild, and test HP LaserJets and LaserJet assemblies all day. If the printer is already plugged into a wall outlet, try another power source in the building that is independent of the one currently being used. 4. You might have attempted an illegal operation, such as trying to download a file to a non-existent directory.
You might have attempted an illegal operation, such as trying to download a file to a non-existent directory. Hp 5100 Printer Price Technicians answer the phone and help customers with printer problems. Press [Go] to continue. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-c01386384 Remove the EIO disk and replace it with a new one.
If you are trying to print A4- or letter-sized paper and this message appears, make sure that the default paper size is set correctly from printers control panel printing menu. and may not be used without advance written permission of PrinterTechs.com, Inc. Some data loss might have occurred. All has been OK until this evening, when to start with I was getting USB malfuntion error ( I use a USB to pin connector).
Hp 5100 Printer Price
MANUALLV FEED [TYPE] [SIZE] Load the requested print media into Tray 1. The printer detected an error. Hp Laserjet 5100 Printer Specifications Turn the printer off and then on. 3. Hp Laserjet 5100tn You might want to add more memory to the printer (see page 107).
Knowledge Centered Support 2016-06-02|Jun 2, 2016 56 Power State as Absent but Switch Operates Normally Knowledge Centered Support 2016-04-06|Apr 6, 2016 448 HP Universal Print Driver (UPD): Property Dialogue Box and http://permamatrix.net/hp-laserjet/hp-laserjet-1018-printer-not-printing.html If this message appears often, simplify the print job or leave Message Explanation or recommended action alternates with Too much data was sent to the EIO card in the specified slot For the locations of sensors, see page 236. 13.5 PAPER JAM or 13.6 PAPER JAM The event log message for a paper-delay jam at the fuser is 13.5. Reseat or replace the interface cable and cycle the power. 3.
Leaving PAGE might degrade performance. A beam-detect error occurred. 1. Thank you! Register · Log In HP Support Forum Home > Printers > LaserJet > HP Laserjet 5100 just started print error HP Support Forums Join in the conversation. have a peek here Press [Go] to print the transferred data. (Some data might be lost.) To print the job without losing data, from the configuration menu in the printer control panel, set and print
FLASH FILE UPERAilUH FAILED The requested operation could not be performed.
Disable the write protection through HP Jetdirect. The problem might be a bad EIO card, a bad cable or connection on the network, or a network problem. Knowledge Centered Support 2016-04-07|Apr 7, 2016 214 How to Obtain the Hostname/Part Number/Serial Number from a Switch using SNMP v2 Knowledge Centered Support 2016-07-07|Jul 7, 2016 861 UPD PCL 6: PCL Remove the EIO disk from the slot indicated.
XX08 Unknown Use genuine HP components for excellent image quality from your printer. Stop it and then RESTART it. Try using the parallel interface, if possible. 6. Check This Out Comment it up...
Check the duplexer and the rear area of the printer for obstructions or damage. 2. Press [-Value+] to scroll through the available types and sizes. To check the fuser, turn the printer off and remove the fuser. Replace the formatter board. (On the 5si, 8000, 8100 this could be a fuser problem.
This change will not take effect until the printer reinitializes. The EIO network card is not working correctly. Reseat the cables. 4. RIGHT CLICK on COMPUTER 3.
Reseat cables to the laser/ scanner and engine controller. 4. Try the DIMM in another slot. 3. Change product Choose from all HP products Enter product serial number Please wait while we process your request. XX06 Replace The printer detects an incorrect printhead cleaner.
For regular 41.3 errors, see 41.3 UNEXPECTED PAPER SIZE on page 197. Check PS1701 and PS1703 in the duplexer for correct operation. Ensure that you have replaced the printhead cleaner together with the printhead. Press [Go] to clear the error message and continue printing.
Check the input area for obstructions, such as print media in the path, damage to the registration assembly, or an out-of-place transfer roller. 3. Remove the printer from any UPS supplies, additional power supplies, or power strips. 2. Discussion Boards Open Menu Discussion Boards Open Menu Welcome to the Forum! Delete files and then try again to print, or turn the printer off and then turn the printer back on to delete all files. (Use HP Jetdirect to delete the files,
Check PS1306 for correct operation.