Home > Hp Laserjet > Hp Laserjet 4200 Error Codes

Hp Laserjet 4200 Error Codes

Contents

Reply With Quote 12-04-2009 #7 J_Lee View Profile View Forum Posts Private Message Senior Tech 100+ Posts Join Date Oct 2008 Location Houston Posts 111 Post Thanks / Like Thanks (Given) Banging will continue for 12 seconds, then it will display the error. This is the small one with the two ribbon cables and various other connections hooked to it, mounted vertically.The Controller board you are talking about I don't see anywhere in the Reinstall all paper input trays. have a peek at this web-site

Figure 21: Removing the paper If the paper has torn, or you still cannot remove it, click here for more information about clearing jams from the fuser area Reinstall the fuser If jammed paper is present, remove it. WiedergabelisteWarteschlangeWiedergabelisteWarteschlange Alle entfernenBeenden Wird geladen... Wird verarbeitet...

Hp Laserjet 4200 Error Codes

Fanning can cause misfeeds. If the error persists contact HP or an authorized service provider. Figure 27: Removing paper Verify the deflector in the printer is working correctly.

As a safety precaution wait 30 minutes for the fuser to cool before proceeding. CAUTION: Static electricity can damage DIMMs. HP Network Issues with JetdirectsParts and Supplies StoreBrother Parts / Supplies Canon Parts / Supplies Copystar Parts / Supplies Dell Parts / Supplies Gestetner Parts / Supplies HP Parts / Supplies Hp Laserjet 4250 Error 13.01.00 Jam In Tray 2 Action Press the (Select) button to resume printing.

You are trying to knock loose any obstructions in the path, like bits of paper, staples.  Insert that in and work it gently up and down.  Reinstall Tray 2 and see Hp Laserjet 4250 Error Codes updated firmware to 4.019.1When the error comes up there is no paper in the paper path, all prints have come out and none has been picked up yet, yet if I Types of messages Status messages Status messages reflect the current state of the printer. http://h20566.www2.hp.com/hpsc/doc/public/display?sp4ts.oid=412144&docId=emr_na-c00633921 If the message persists, contact HP Customer Support.

Action Turn the printer power off and then turn the printer power on. Hp Laserjet 4250n 49.4c02 Service Error This cleans up the permanent storage by removing old areas that are not being used. alternates with 52.XY PRINTER ERROR To continue turn off then on Description A temporary printer error has occurred. It doesn't receive tray.

Hp Laserjet 4250 Error Codes

Figure 20: Opening rear-output bin Remove the fuser by pushing up on the blue tabs and check for paper in the printer as well as in the fuser. Hold down Cancel Job while turning the printer power on. Hp Laserjet 4200 Error Codes If the message persists print a Configuration page and check the printer settings to determine which values have changed. (To print a Configuration page, open the Information menu at the printer Hp Laserjet 4200 Cartridge Installed Message hope this helps.

If the error does not clear, turn the printer power off and then turn the printer power on. Check This Out by unknown on Apr 6, 2014 at 12:57pm Add comment Please sign in to comment 0 I was getting a 13.06 and read Here to replace the formatter. as cant find it in the service manual thx in advance update, i corrected that problem, i ran a 50 page print, and it locked up, took toner out, and the Action If the incorrect size was selected, cancel the job or press the Help (?) button to gain access to help. Hp Laserjet 4200 And 4300 Series Printers Drivers

Next, lower the rear output bin cover as shown below. Be careful not to spill it on yourself or into the printer.) NOTE: NNOTE: If the jammed paper is difficult to remove, try opening the top cover all the way to Tray Lift Motor Mount Defect The motor gear does not engage the tray gear, preventing tray from lifting and causing subsequent 60.X Error. Source Open the top cover and remove the print cartridge.

NOTE: Avoid spilling loose toner. Hp Laserjet 4250 Error 13.20.00 Jam In Tray 2 If the error persists, replace the HP Jetdirect card (EIO card). Remove the rear output bin by pushing the left side of the bin to the right and then removing the hinge pin from the slot in the chassis of the printer.

If the above action does not solve the issue, contact HP, or contact an authorized service provider.

alternates with 51.XY PRINTER ERROR To continue turn off then on Description A temporary printer error has occurred. Recent products: HP LaserJet 4200 Printer series Troubleshoot a problem Help Other Knowledge Base options Search HP Support Center Most viewed solutions Advisories, bulletins & notices Manuals Setup & install Learn Figure 24: Removing jammed staple Insert the staple cartridge into the stapler unit and rotate the stapler unit toward the rear of the printer until the unit snaps into place. 13.98 Paper Jam NOTE: A loss of data will occur.

All rights reserved. If the message persists, contact HP Customer Support. The stapler/stacker LED blinks in amber. have a peek here Kategorie Praktische Tipps & Styling Lizenz Standard-YouTube-Lizenz Mehr anzeigen Weniger anzeigen Wird geladen...

Printing can continue, but behave unexpected in response to the changed settings. If the error does not clear, replace the duplexer. Remove the pages from the output bin and press the (Select) key to continue printing. Tech Support Support Home PageMaintenance Kit InstructionsOther instructionsTroubleshootingArticles, news, blog Featured Articles HP Error CodesEntering Service ModeService mode PIN codesCounterfeit parts challengeCold reset instructionsClearing maintenance countJetDirect Reference GuideHalf-way testRepetitive defect rulerTestimonialsInnovations

Figure 61: Sealing tab on end of print cartridge 1 - Sealing tab bent and removed from end of print cartridge CAUTION: Avoid touching any black toner on the tape. Check the configuration of the EIO (HP Jetdirect card) and the host computer. Figure 42: Plugging the power cord in Reinstall the optional duplexer, if it was removed. Make sure that the paper is neatly stacked and that the paper guides are not too tight against the paper.

Fusers are a consumable part and are sold as part of a maintenance kit; it is expected over the life of the printer you will replace the fuser several times. changed fuser mode from normal to high 1 and 2 so far none of this has worked.symptons: can print a few prints then error or sometimes can print 40-50 or more Figure 43: Reinstalling duplexer Turn the printer power on. top 57.X PRINTER ERROR To continue turn off then on Description A temporary printing error occurred in one of the printer fans.

Reply With Quote 12-10-2009 #9 Realtech View Profile View Forum Posts Private Message Senior Tech 100+ Posts Join Date Oct 2009 Posts 103 Post Thanks / Like Thanks (Given) 0 Thanks