Home > Hp Laserjet > Hp Laserjet 4200 Error 13.06

Hp Laserjet 4200 Error 13.06

Sign Up Login Add Question utl asked Oct 3, 2006 at 3:13am 0 HP LaserJet 4250 HP 4250 13.06.00 Fuser output paper stop ! Click here for instructions on how to print a Configuration page. If the above action does not solve the issue, contact HP, or contact an authorized service provider. Ensure that tray is not over-filled or damaged. have a peek here

On the right side of the stapler/stacker, turn the stapler unit toward the front of the printer until the unit clicks into the open position. If paper is present, remove it. Open the back door and lift the top off. These messages typically alternate with the “Ready” or “Status” messages and remain displayed until the (Select) is pressed. https://www.laserzone123.com/4200-paper-jam.html

top 50.4 FUSER ERROR Description The problem exists with the customer’s line voltage. See Dc controller PCA. 7 If the error message appears frequently, see Paper-path troubleshooting. Rear output bin 1.

NOTE: A loss of data will occur. We solve most HP 4200 printer with paper jam errors and image defects problems by replacing roller kits and maintenance kits. TIP: When you replace the fuser, make sure that it is fully seated into the product. Press the (Up Arrow) and (Down Arrow) buttons to step through the instructions and/or refer to the following steps.

Close the door. Make sure it locks into place. If the message persists, contact HP Customer Support. http://www.fixyourownprinter.com/posts/75177 Like toner cartridges every  supplier claims their product is the best.

Fuser Removal ProcedureWait 5 to 10 minutes Before Removing the Fuser to allow it to cool down and make sure you unplug the machine. You can also turn the jam-clearing wheel that is located on the side of the fuser to attempt to eject the jammed paper. Hot water sets the toner into the fabric. My 4th visit and now DC controller is Next ?...

HP 4200 13.12.08 paper jam error message indicates the output bin page-detection sensor has been active for longer than the specified time. 4200 13.12.09 message indicates that the stacker or stapler

The menu map will print out. Action Turn the printer power off and then turn the printer power on. Genuine HP Q1338A Black Toner Cartridge!

Whenever the printer is ready, not busy, and has no pending warning messages, the status message “Ready” is displayed if the printer is online. navigate here Hold the DIMM with your fingers against the side edges and thumbs against the back edge. Easy to get to. alternates with 68.X PERMANENT STORAGE FULL To continue press (Select) Description A nonvolatile storage device is full.

Los Angeles County Los Angeles La County LA Downtown L.A Greater Los Angeles West L.A West Los Angeles Beverly Hills Culver City La Downtown Brentwood Century City Marina del Rey Highland top 64 PRINTER ERROR For help press? top 52.XY PRINTER ERROR For help press? Check This Out by hyedipin on May 10, 2013 at 12:32pm Add comment Please sign in to comment 0 To be honest it sounds like you have a bad fuser.

Figure 10: Checking the quality of the inserted paper Slide the tray back into the printer. If a message persists after performing all of the recommended actions, contact an HP-authorized service or support provider. Remove all paper from the output bin.

Try printing a job from a different program.

How about just replacing the solenoid with a new one if it is not too expensive? - hyedipin 0 They use the felt on the bottom of furniture legs. Pressing the Select (check) button should clear the message. CAUTION: Ensure that all jammed paper is removed before closing the cover or tray. Is there anything I can do without having to pay another $190?I am ready to toss this printer out, but if there is any way we can try another fuser with

A nonvolatile storage device is full. top Provide feedback Please rate the information on this page to help us improve our content. If the above action does not solve the issue, contact HP or an authorized service provider. this contact form Turning the printer off and then on can clear some of these messages.

If the message persists, contact HP Customer Support. CAUTION: Do not fan the paper. There is no other thing that can cause that specific problem as the Manual feed uses the same paper path except for the small portion that comes up from the paper top 55.X PRINTER ERROR For help press ?

Pressing the Select (check) button should clear the message. An attempt might have been made to transfer too many macros, soft fonts, or complex graphics. 21 Page too complex The data (dense text, rules, raster or vector graphics) sent to Action Open the top cover and remove the print cartridge. Turn the printer off and then back on.

by moe on Apr 25, 2013 at 11:18pm Add comment Please sign in to comment Thanks Moe. The issue can be caused by a firmware error, invalid print commands, corrupt data, invalid operations, poor quality parallel cables, poor connections or specific applications. 49.24.02 error, 49C02 error and 49C06