Home > Hp Laserjet > Hp Laserjet 4100 Error Codes

Hp Laserjet 4100 Error Codes

Contents

Well are you sure that was your problem. To make sure you replaced the right part, how did you replace the tray 2 pickup assembly. You'll have to remove the top of the printer from the tray and take the top metal plate off to access it. by moe on Oct 24, 2007 at 9:05pm Add comment Please sign in to comment 0 13.1 is a paper jam error at the paper cassette.Try using the MP (flip down) Source

When you powered the printer on, it just started feeding blank pages out of tray 2 continuously. BrokenPrinter1 33,684 views 5:50 Kit 4100 - Kit Hp 4100 - Kit Mantenimiento 4100 - Duration: 5:37. by startrek133 on Nov 11, 2009 at 11:10am Add comment Please sign in to comment 0 Try replacing the sensor that sits in the ecu cavity and is connected via yellow Do you wish to proceed to the home page of the new product? http://h20564.www2.hp.com/portal/site/hpsc/public/psi/troubleshootResults?sp4ts.oid=83436

Hp Laserjet 4100 Error Codes

by unknown on Sep 10, 2014 at 10:48am Add comment Please sign in to comment 0 Thanks so much for this piece of advice / tutorial. any other advice ? and may not be used without advance written permission of PrinterTechs.com, Inc. I have replaced the rollers; however, this has not fixed the issue.

If the computer sending the job has an issue it is possible it will send the job but not in a constant stream so it is possible another job could sneak and even after all that , it still just pulls one blank paper and than jams with a 13.1 error .. by dmzcompute on Feb 27, 2007 at 6:51pm Add comment Please sign in to comment 0 I have the same 53.10.03 error which only appeared after I tried to add memory. Hp Laserjet 4100 Driver Preview post Submit post Cancel post You are reporting the following post: HP LJ4100 error 57.4 This post has been flagged and will be reviewed by our staff.

I turn my 4100 on and print a few pages, then I print again and this turn I get a blank page followed by a Paper Jam 13.1 Error. Do I need to remove filings from the clutch? Open the top cover and remove the toner cartridge. http://www.fixyourownprinter.com/posts/15471 It is located on the right side of the feeder unit and you have to split the printer into two parts so as to have access to the feeder unit and

If you cannot find your product on this site, go to HP Support Center - Hewlett Packard Enterprise. Would a bad solenoid create the same symptoms? by startrek133 on Nov 11, 2009 at 6:35am Add comment Please sign in to comment 0 ok DMZ , i checked that sensor flag and its fine its not broken or Sorry, there was a problem flagging this post.

Hp Laserjet 4100 Not Printing

Just take the spring off and the L-arm will come off the solenoid. Troubleshoot a problem Software and drivers (22) Windows (9) Macintosh (11) Other (Unix, Linux, Novell, etc.) (2) Installation and configuration issues (8) Printing (2) Windows (4) Other (Unix, Linux, Novell, etc.) Hp Laserjet 4100 Error Codes I replaced the thin drum just below the cartridge.I send a job through, "jams", sends out a blank, then I lift the top access panel, shut it again and it will Rg5-5277 If I pull the tray out a little it will print OK but I can see nothing wrong with the tray and I can hear all three microswitches click when the

If the clutch does not separate you have the new type and it will not be the issue. this contact form Solenoid is in the right front corner. I was thinking of doing a disassembly video for the less mechanically inclined individuals and include a piece of our felt. If you would post the problem you are having maybe someone can help you. - dmzcompute 0 HP 4100DTN working fine with multiple pages from tray 2 .. Hp Laserjet 4100 Manual

Loading... paper late jam. The solenoid is attached to the end of the wires. have a peek here Your tip off should be that another tray works ok.

Add to Want to watch this again later? What are your thoughts?Thanks for following up, dmzcompute. BrokenPrinter1 19,264 views 4:14 HP LaserJet 4000 Series Maintenance Kit - Duration: 3:56.

If the paper moves forward and then comes back a bit, the problem is with the clutch in the tray.

I scrape the goo off and put a piece of thin sticky back felt on it to keep it from sticking and dampen the noise. No difference printing local paper path test, LPT1 or network connection.What I've done:Replaced the fuser, face down/delivery assembly, Tray 2, both tray 2 PU rollers, formatter board and the engine board. We disassembled the entire tray 2 assemblyand completely cleaned the solenoid and it worked! CHECK OUTPUT DEVICE (DELIVERY PATH) WAIT FOR PRINTER TO REINITIALIZE CHECKING PAPER PATH xx.yy PRINTER ERROR CLOSE TOP COVER Home About Us Contact Us Search Site Map Printers Supplies Accessories Parts

Your suggestion worked.I cleaned the gunk from the solenoid and no more extra sheet of paper getting stuck in the printer.The hardest part is figuring out how to remove the top by moe on Jan 12, 2012 at 12:27pm Add comment Please sign in to comment 0 I have an HP LaserJet 4100 that throws a 13.1 paper Jam error. So somtimes the "L" arm goes to the center and when power is turned off it stays there sticking with the glue and does not return and stop the paper movement. Check This Out Cleaned and lubed all shafts gears and rollers.

by granto999 on Feb 15, 2010 at 9:00am Add comment Please sign in to comment 0 I am having a similar issue as most of you, but not sure how to If you believe this post is offensive or violates the CNET Forums' Usage policies, you can report it below (this will not automatically remove the post). Reassembled, and I got error 13.1 after it seemed to just spin (no paper movement/output).