Home > Hp Laserjet > Hp Laserjet 4050 Error 13.1

Hp Laserjet 4050 Error 13.1

Being that I haven't torn one of these apart, I took my time following the service manual and managed to get all the way down to the solenoid.Like others were saying, by dmzcompute on Nov 11, 2009 at 7:30pm Add comment Please sign in to comment 0 I have the same problem. Pull the tray out, you are looking at the separation roller. by dmzcompute on Nov 21, 2006 at 5:25am Add comment Please sign in to comment I have about 6+ older 4000/4050 printers doing the same thing especially from TRAY 3.I thought http://permamatrix.net/hp-laserjet/hp-laserjet-4050-manual.html

The repair took about 40 minutes. ASAP ..to see if we can repair this before to buy a new one ...I am using this printer for my home bussiness so I am stuck I do apreciated, by Add Stickiness To Your Site By Linking To This Professionally Managed Technical Forum.Just copy and paste the BBCode HTML Markdown MediaWiki reStructuredText code below into your site. HP Printers Forum Next remove the formatter assy from the right side.

BrokenPrinter1 44,158 views 11:30 hp Laserjet p2035 and p2055 how to remove and install a fuser PART 1 - Duration: 10:49. The manual feed tray is still sucking in all sheets of paper at once. I swapped the paper sensor between tray 2 & 3 (just to prove that they are both working).

See:179 | Removing the tray 2 paper-feed plate After removing the 4 screws, you can lift the plate from the plastic part of the printer tray. AND tray1(bypass) is pulling in whole stacks.(i realize these are most likely 2 seperate issues but found it interesting that he described exact probs i had). Hopefully this little synopsis will help. BrokenPrinter1 61,349 views 5:35 HP LaserJet 4000 Intro and Rebuild Part 2 - Duration: 18:42.

You'll receive secure faxes in your email, fr… eFax Advertise Here 778 members asked questions and received personalized solutions in the past 7 days. Finally the office tried using the manual feed and would stick in 10 pieces of paper at a time in the manual feed tray. If it fall back to where it is not attempting to go up the slot, then the problem is the "CLUTCH". http://www.fixyourownprinter.com/posts/1646 by moe on Jul 3, 2001 at 9:07am Add comment Please sign in to comment 0 Bad torque limiter.

Thanks FYOC.com, you rock. I also replaced all rollers.thanks again.g by garrett on Feb 21, 2003 at 3:57pm Add comment Please sign in to comment 0 We have 30+ HP LJ 4000 printers, the primary That material over time disintegrates and all that is left is the glue which held it. No difference printing local paper path test, LPT1 or network connection.What I've done:Replaced the fuser, face down/delivery assembly, Tray 2, both tray 2 PU rollers, formatter board and the engine board.

Solution: For 13.1 and 13.2: 1. http://fixyourownprinter.com/posts/43012 Now how do I take it out without breaking it?Prink. Is it possible to just remove tray 3 completely? Does the pickup roller turn and does the paper feed bar lift when you run a paper path test from tray 1?

Just follow the wires that run into the square box with gears on the right side of the plate. http://permamatrix.net/hp-laserjet/hp-laserjet-error-19-1.html I'd like to find that pad that DMZ was talking about but not sure what 'splitting the printer in 2' refers to. :)Any help would be... Mainly those where the only things I did to look for the 4 half moon rollers. Updated the printer driver to HPBF042G.dll for testing without any changes.Any thoughts??Brad in Florida by blh72 on Jan 5, 2010 at 1:12pm Add comment Please sign in to comment 0 Sticking

It has two video ports on it – VGA and DisplayPort. will check the sensor flag and see what i find , thank you !! I tore it down & checked the solenoids (tray 3 & 2) with an ohm meter & both of them are the same. Check This Out Most times both trays for your model will have them.

by moe on Oct 24, 2007 at 9:05pm Add comment Please sign in to comment 0 13.1 is a paper jam error at the paper cassette.Try using the MP (flip down) I told him the item was a coupler which connects the 4 half moon rollers to the main gear assembly. by moe on Jan 5, 2010 at 5:13pm Add comment Please sign in to comment 0 Removed the tray2 cover and cleaned the solenoid.

Can't be the clutch: Swapped tray 2 and 3, same problem.

If the rollers turn, then on the paper tray itself remove the separation roller and remove the clutch behind it a put the roller back on the tray. While testing tray 2 I can see the rollers picking up the paper. Couldn't seem to get tray 3 separated so I could see the mechanisms inside. by unknown on Jul 3, 2001 at 8:36am Add comment Please sign in to comment 0 You can't always go by the look of the rollers.

Pull the tray out, you are looking at the separation roller. However I have to have a starting point somewhere... when I saw that it was wired just so, I carefully put it back together with electrical tape as it was. this contact form To the user with the problem, you say the paper moves forward 2 inches and then falls back into the tray.

The foam in the solenoid was flaten and there was a delay in the release due to that being sticky. i DO know the right vocab and have significant experience. Above tray 2 covers a lot of area. You have to take the metal top off of the tray to get access to the solenoids, which are at the front of the tray adjacent to the pickup roller shaft.

BrokenPrinter1 40,577 views 6:55 HP LaserJet P4015 Maintenance Kit Instructional Video - Duration: 7:45. could there be a dirty sensor somewhere? Would a bad solenoid create the same symptoms?