Home > Hp Laserjet > Hp Laserjet 4000n Error Codes

Hp Laserjet 4000n Error Codes

Also make sure the flag and post it is attached to is snapped into the output bin correctly. Test with paper from another, unopened bundle. Once you reach 200,000 pages on HP LaserJet 4000/4050 and 4200 printers the error message appears and you need to reset the maintenance count to zero to make the message go Check for nicks on the plastic in the feed path which can be filed down, if needed, so the problem does not recur. have a peek here

Replace the DIMM that caused the error. 54.1 REMOVE SEALING TAPE alternates with FROM TONER CARTRIDGE The toner cartridge has been installed without removing the sealing tape. 1. There is actually a mathematical equation for this, but it is not handy. Add paper. This is important since if it happens from both trays, then you are looking at the dc controller (main board) or the registration assembly.

Press the SELECT key to roll out this improvement the new printer default. In order to get to it you have to separate the printer into its 2 halves and then remove all the screws that secure the top plate of the paper feeder Turn the printer off. 2.  Simultaneously hold down the minus side of the Item key, and the minus side of the Value key. 3.  Turn the printer on while holding these

Didn't have a manual to see what that error meant. Service Printer Canon MP287 Error P10 Slide B200/ P10 Rule ip2770, Canon Mp237 Service Printer Canon MP287 Error P10 - Slip B200/ P10 Printing device Canon - you do have a... All images and logos used with permission from the respective owners. Home Page Technical Resources Lexmark Error Codes HP Error Codes Tech Support Blog HP Drivers Lexmark Drivers Terms & Conditions Product Conditions Definitions Web Order Minimum Returns Shipping Freight

plz ~~~help~~~ by unknown on Sep 21, 2006 at 10:15am Add comment Please sign in to comment 0 Does the error occur from both the manual tray and tray 2 or System error 71:04 Problem allocating memory. I found my removed, and fixed it. http://www.metrofuser.com/error-codes System error 05:10 (DJ 800 only) Formatter card failure, or Formatter card not detected System error 05:10 (DJ 500 only) HP-GL/2 accessory card failure System error 06:03 (DJ 800 only) Hard

Reinstall the toner cartridge and close the top cover. 54.4 PRINTER ERROR alternates with CYCLE POWER TO CONTINUE A problem exists with the customer’s line voltage. 1. System error 93:10 Ink System startup failed. System error 21:10 A problem has been detected with the Service Station assembly. by levarfan on May 27, 2010 at 7:57pm Add comment Please sign in to comment 0 I removed the clutch in tray 2 a long time ago, due to errors.

System error 85:10 Paper-axis shutdown (during the paper advance test). Visit our technical blog for more HP and Lexmark service articles. Note that these half moon shaped rollers don't have to be worn down to the bottom of the grooves, so you might think that they are ok by casual look.Of course Often, though, it's a paper jam in the front of the machine.

The printer was continually printing blank pages and displaying 41.5 Printer Error. navigate here If the message persists, reseat the fuser. by dmzcompute on Nov 26, 2004 at 3:23pm Add comment Please sign in to comment 0 I have seen 2 people talk about this procedure in the last few days... Works great now.

System error 64:03 USB port communication problem. When that happens the first page is a blank page, the error 41.5 appears and then the next pages appear with no problem. The memory starts counting at 000MB immediately after you turn the power on. 4. http://permamatrix.net/hp-laserjet/hp-laserjet-4100-error-codes.html HP LaserJet printer repair with common error code failures!

System error 73:04 Server error. To the left is a piece of beige plastic held by a clip. To assess the detachment rollers, perform the accompanying directions: NOTE: Blank pages will likewise print out with a 41.5 blunder.

System error 22:10 A problem has been detected with the Ink Supply Station.

I also cleaned out the particles on both of the paper tray clutches. They never asked what was wrong or investigated, they just turned it off. and may not be used without advance written permission of PrinterTechs.com, Inc. Send an Email Toll Free: 877-365-1903 About us Terms Contact us Help Login Brand : All brands HP Models Lexmark Models Xerox Models Model : Choose a brand

Press SELECT. If the short cut method doesn't reset the maintenance count then you will need to go service mode to manually reset the maintenance count to zero. System error 55:11 A problem with the line sensor has occurred. this contact form If a maintenance kit or fuser was installed right before getting the error then pull the fuser out and check the sensor on the left side of the fuser.

Great stuff. Press [+] to cycle choices until the wanted paper trays show up. If the printer is already plugged into a wall outlet, try another power source in the building that is independent of the one currently being used. 4. HP LaserJet 4000n and 4050 printer failures with service error codes!

This 4000N usually leaves a blank page in the printer after a print job (between registration and fuser) and displays no errors. You have to put a replacement pad on them. Wait for RESET MAINTENANCE COUNT to be displayed and then release both keys. NOTE: Some versions of the 4000, 4050, 4100, and 5000 will NOT have their maintenance count reset Single sided printing on tray 1 paper path do not go thru that assy but doulde sided does after it went into the duplexer.

Home Contact Us Laser Printer Service Laser Printer Repair Laser Printer Parts HP LaserJet Service HP Error Codes HP Plotter Repair Discount/ Free Offer Company Info Los Angeles and Orange Verify accessory connection. 57.X PRINTER ERROR A fan failure was detected. X Description: hp 4000 50.1 is Low Fuser temperature 50.2 is Fuser warm up service 50.3 is High Fuser temperature 50.4 is Low/Bad line voltage (Printer hooked up to UPS) 50.5 HP Laser Jet 4000 13.5 PAPER JAM 13.6 PAPER JAM Paper delay jam at Fuser (13.05) or Paper stopped jam at Fuser (13.06). 13.10 PAPER JAM Paper delay jam at paper

Ive also chged those sensors but still the same. Measure the resistance between the fuser connectors. And a worn or loose separation roller can cause this as described in previous posts.Any one of these rollers can mean slipping on the paper, which is what causes the jam Had the same error.

by unknown on Feb 11, 2010 at 7:42am Add comment Please sign in to comment 0 I just wanted to add that while I see it alot with the torque limiter Tech Support Support Home PageMaintenance Kit InstructionsOther instructionsTroubleshootingArticles, news, blog Featured Articles HP Error CodesEntering Service ModeService mode PIN codesCounterfeit parts challengeCold reset instructionsClearing maintenance countJetDirect Reference GuideHalf-way testRepetitive defect rulerTestimonialsInnovations Turn the printer on. 4. eCommerce Solution : k-eCommerce On Sale About Us Contact Us Order Status FREE TECH SUPPORT (877) 755-5300 Login My Cart (0) Printers Printer Supplies Printer Parts Printer Accessories Error Codes Our

The funny thing is, when I first turn the printer on, it says checking printer, and spits out about 4 or 5 blank pages, and then jams. Pull the sealing tape tab to remove the strip. 3.