Home > Hp Laserjet > Hp Laserjet 4 Printer Error 51

Hp Laserjet 4 Printer Error 51

ERROR 67 - Defective formatter PCA 2686A/D, II, IID, IIP,III,IIID,IIIP,4,4+,4P - Defective formatter board, try reseating the connectors and any accessories you may have plugged in On the 4Si this could If you are seeing repeated error codes of 51.10 or similar, you should replace the laser scanner.   Click here to view installation instructions Click here to order a replacement laser When reseating the connector, use a small flat blade screwdriver to fully seat the female connector ends. by unknown on Oct 11, 2003 at 7:57am Add comment Please sign in to comment 0 The HP4 and 4+ use different scanner assemblies. http://permamatrix.net/hp-laserjet/hp-laserjet-5100-printer-specifications.html

Reply 0 Reply 0 0 Everyone's Tags: EBCOMMIPG View All (1) davidzuts Regents Professor Posts: 4,703 Member Since: ‎01-17-2009 Message 2 of 10 (18,633 Views) Report Inappropriate Content Re: HP M602 Bad cable from laser scanner ass'y to D.C. If it doesn't clear the error you may have one of the problems listed below The HP LaserJet II/IID/III/IIID, Apple LaserWriter II and many other Canon SX engine based printers have The cause is a bad cable between the DC Controller and the laser/scanner assy. http://fixyourownprinter.com/posts/13257

Faulty connectors. 4. Still if the issue persists.Replacing the laser scanner assembly will replace the issue.Regards,Ram Reply 0 0 Sohail_A_Khan Tutor Posts: 21 Member Since: ‎05-13-2014 Message 6 of 10 (18,489 Views) Report Inappropriate If the error can be reset by turning the machine off for 20 minutes, it is most likely the AC power block. The page containing the error will automatically be reprinted. 2.

The printer has experience an internal hardware error. 2. There is no charge except to cover the costs of copying. You can often verify the AC power block as the problem by opening the rear door of the printer and observing the heater lamp glow when turning the printer on - If your S/N falls in the range, then look for a RED dot on the power supply in one of two locations.

X = description: 1 = Illegal input or bad accessory connector 2 - Illegal output The page containing the error will automatically be reprinted. 1. If you have an IR detector (as used for testing remote controls) then undo the screw on the scanner - not the fixing screws that hold the scanner in place - This is sometimes indicated by the very distinct and pungent smell of a printed circuit board burning. http://www.repairfaq.org/samnew/printfaq/pcfljec51.htm Hewlett Packard Search -- Select Type -- HP DesignJet HP Envy HP LaserJet HP LaserJet Enterprise HP LaserJet Pro HP OfficeJet HP OfficeJet Enterprise HP OfficeJet Pro Series HP Photosmart HP

Add more memory or simplify the print job. You would have to find another 4+ scanner assy. Simplify the job by removing font changes etc. The HP LaserJet 5P/6P indicates service errors in a similar manner to the 4L/4ML except there are 5 indicator lights.

If you think you have received a fake HP Support message, please report it to us by clicking on the blue “Report Inappropriate Content” button above the message. http://www.printertechs.com/printer-troubleshooting/hp-error-codes/195-numeric-error-codes-50-59-hp-laserjet You may need additional memory. 4L Same thing with to much data or the page is to complex. Replace the formatter and/or firmware DIMM. 4. Thanks Respond to this 0 An error 51 is a beam detect error related to the laser/scanner assembly.

On the II and III Series and the IIISi/4Si, make sure at least one of the two drum sensitivity tabs are present. http://permamatrix.net/hp-laserjet/hp-laserjet-1018-printer-not-printing.html themaritimeman 9,895 views 28:28 How to replace the rollers on a hp laserjet 4plus or 5 exit assembly - Duration: 5:55. The outer gear should rotate in one direction only with a spring action which limits it rotation. longlifeprinters9 9,460 views 10:12 RG5-0886 fix the Accordion style paper jam hp laserjet 4plus or 5 PART 1 - Duration: 5:36.

Start be reseating the 2 cables (one under the flap) that go to this unit. Advertisement Autoplay When autoplay is enabled, a suggested video will automatically play next. Replace the fan. Check This Out BrokenPrinter1 5,367 views 8:52 HP LASERJET SERVICE IN 5 MINUTES - Duration: 4:38.

This notice is included in its entirety at the beginning. 2. Faulty laser scanner cable connectors. 2. If not replace the motor or drive circuit as required.

HP LASER PRINTER 3050, 3052, 3055, 3390, 3392 1.

I usually remove them and reseat. HP LASER PRINTERS 3015/3020/3030MFP 1. Reseat the cable and use only high quality IEEE 1284 compliant cables. 5Si Are you using a non-HP MIO device? Defective laser scanner assembly. 4.

HP LASER PRINTERS 4L, 4P, 5P, 5SI 1. The official fix is to replace the scanner, the cables (electrical and fiber optic) between the scanner and the DC controller, and then the DC controller until the fault goes away. If you do, then, alas the problem is most likely in a custom chip, and it's time to replace the DC controller. this contact form On older style printers this is often caused by a bad main motor. (Older style printer being printers with halogen heating elements in the fuser - 4, 4+, 5, 4si, 5si,

Over the paper tray there's a flat black box. Do not look up this channel - it can output laser light. A beam detect error or laser error.2. If the lamp begins to heat (you can feel the roller, but be very careful it's HOT ) its not the lamp or the thermal fuse and is most likely the

Replace the scanner ass'yHP COLOR LASER PRINTER 4600, 5500 ERROR 51.1, 51.21. The thermal fuse and thermistor are also possible causes of a 50 Service error. I may be contacted via the Sci.Electronics.Repair FAQ (www.repairfaq.org) Email Links Page. <> HP LaserJet error code 51 "On Remove the screw securing the lug to the terminal.