Home > Hp Laserjet > Hp Laserjet 4 Plus 22 Par Io Error

Hp Laserjet 4 Plus 22 Par Io Error

You can remedy this by replacing the paper guide plate assembly, RG5-2248-030. Live Scores Programming Apple Watch Beautiful Breasts Office Windows 7 Windows Server Phone Application Server Dropbox in Current Tags (Entire Site) All Tags » laserjet (RSS) Browse by Tags 1000 1012 ERROR 24 - Job Memory Full The print job is too complex to be processed. This LED pattern, shown while pressing the front panel button, indicates a fuser error. http://permamatrix.net/hp-laserjet/hp-laserjet-error-10-10-00.html

ERROR 18 - MIO Not Ready The printer is not connected to a LAN when it's expecting to see a LAN. No, create an account now. Computer is G4 with 1.5 Gig memory 3. Defective formatter PCA - replace On the HP Laserjet 4/4+/4Si/4V/5/4P/4MP the 53.XY.ZZ error code is decoded as follows: 53 (XY-ZZ) where X- Hardware Type: 0 = ROM 1 = RAM Y

Similar Threads - laserjet problems HP 3005n Laserjet printer problem wolfworx, Oct 16, 2016 at 2:10 PM, in forum: Hardware Replies: 5 Views: 68 flavallee Oct 17, 2016 at 10:29 AM ERROR 51 - Service Improperly seated toner cartridge - remove and reinstall Laser shutter blocked or damaged Damaged fiber optic cable Defective Laser PCA - replace I/IID/III/IIID Defective toner cartridge - Simplify the print job.

Cannot access WIN95 shares with Remote Registry 5. This type of error can be caused by invalid print commands, corrupt data, or invalid operations. There may be a problem with connection between the memory chip and DC controller. Peachykeen, Dec 1, 2015, in forum: Hardware Replies: 5 Views: 279 lochlomonder Dec 1, 2015 bios problems again oldgadget, Oct 12, 2016 at 3:35 PM, in forum: Hardware Replies: 7 Views:

When they open and print them through Terminal Server to their local printer, the process will take close to 2 minutes before the job starts. You could also have a defective or dirty exit sensor. Listen to the scanner motor, it should have a distinct "whirring" sound as the printer prepares to print. http://www.verycomputer.com/14_34eeb70694e6cad4_1.htm This board takes the input from the two sensors and provides info to the DC controller.

Indicates a loose cable connection or a bad or poor quality cable. - Reseat the cable and make sure you are using a high quality cable.(IEEE1284) HTH bob Quote:> Just started When you have an error, reference the PrinterSupplies.com web site and look on this printer errors page for your number. Back back to top How did we do? Mike Posted on Thursday, August 09, 2001 - 9:29 pm: There is no such error code as 421 on the LJ4+ check the Code again stevo Posted on Friday, September

ERROR 89 All Printers (except 5L/6L) The PostScript ROM's have bent or broken pins inspect the pins and reseat if necessary Check to see that the ROM SIMM's are in the http://www.mj-printers.com/discus/messages/22/1180.html?1168123238 ERROR 14 - No EP Cartridge or No Toner Cartridges No toner cartridge or cartridge not fully seated - pull it out and install it again. The problem is every time I send a job to the printer from the PC,I get a "22 Par IO Error" on the printer control panel. This requires removal of the cover, an unpleasant task, and measurement of the fuser terminals.

To much data sent to the I/O port - clear data with GO or Continue, data may be lost Is the computer on?! navigate here Extremely heavy or thick paper is also a problem. If it's broken, you will need to replace the sensor flag. Measure the resistance between pins one and two of connector J102 - they should read 30 +/- 10 ohms.

On the III, IIID, IIIP, enable page protect if you have and additional 1 MB of memory installed. Manual Feed - waiting for you to add sheet of paper for manual feed from single sheet slot. So is there a way into making 'sue' replace'bob' without remapping the drive everytime?Isn't that exactly how the Homes shares work?I'm not sure I get it...Steve******************************************************************Stephen L Arnold http://www.rain.org/~sarnold#include ******************************************************************Paul CrittendenComputer http://permamatrix.net/hp-laserjet/hp-laserjet-error-19-1.html Keep trying, Steve-x8086 Steve-x8086, Sep 29, 2000 #2 phobiussno Joined: Nov 21, 1999 Messages: 718 Buffer overrun error...

Try printing an engine test (sheet of vertical lines) by pressing the engine test button located behind the access hole on the lower front of the printer. Remove and reseat the optional interface card. Replace if problem persists IIIP/IIP/IIP+ Paper feed problem - check feed/pickup rollers for movement and wear.

Early models of these machines had a scanner assembly which contained a manufacturing problem causing the scanner speed control IC to overheat and burn out.

You need to check the configuration of your printer and drivers, reset the printer, try issuing an initialization command from within the application. Simplify the print job. However, the number displayed will point you in the right direction. A buildup of toner on the edges of the tray which slide into the printer can sometimes cause problems.

Can't seem to figure out why it is doing this? Join over 733,556 other people just like you! If I leave the printeralone and let it handle the problem (i.e. http://permamatrix.net/hp-laserjet/hp-laserjet-5m-53-12-03-error.html Sensor Arm Stuck or Broken - check for free movement of the sensor arm.

Advertisements do not imply our endorsement of that product or service. I have just recently replaced both pc's that were attached to each printer. XX Description 00 memory error on the cartridge or 01 memory device not found 10.00.00 Black print cartridge 10.00.01 Cyan print cartridge 10.00.02 Magenta print cartridge 10.00.03 Yellow print cartridge Supplies Posted to HP (Forum) by hardware on 05-29-2009 Problem: PostScript print jobs across WAN We scan 10-15 page PDF documents to our remote location.

If the problem persists and is application specific, verify proper setup with application vendor. You can verify this by substituting a known good DC controller if possible. Be careful with labels, use only labels designed to take the heat generated by the fuser assembly. On the 4/4M/4+ and 5: The print job is to complex, enable page protect from the control panel and from the software.

Need the code to reset the counter and remove the annoying "maintenance kit" reminder. Click here to join today! Add more memory or simplify the print job. If you're not already familiar with forums, watch our Welcome Guide to get started.

Take a sharp tool, like a razor blade and scrape the buildup off these edges. Classic II Memory Increase 3. How about the I/O port - damaged, seated properly, pins not bent? 4+/5P/5 The computer and printer aren't talking because of improper signal protocols. We also recommend you replace the Ozone filter at this time.