Home > Hp Laserjet > Hp Laserjet 4 Paper Jam 13

Hp Laserjet 4 Paper Jam 13

Contents

The printer prints the report. Check the pickup feed and separation rollers for unusual wear. Both at certain times can block or unblock the sensor. by Anonymous on Jan 1, 2006 at 6:33pm Add comment Please sign in to comment 0 the back door is closed. http://permamatrix.net/hp-laserjet/hp-laserjet-p1007-paper-jam-problem.html

If it jam before it > reachs the Fuser, there is a sensor under the toner cartridge. PartsNow Marketing 19,103 views 5:20 Hp laserjet 4 plus - Duration: 1:04. Wait until the warm-up period finishes and your printer is idle and silent before you proceed. So take the top cover off.

Hp Laserjet 4 Paper Jam 13

Continuous paper jams. Rating is available when the video has been rented. I have, however, seen the registration sensor go bad which is on a board on the paper input unit. Then actuate the linkage up there manually with your finger and see if it is sticking.

Use a flashlight to thoroughly look for torn pieces of paper. About Us Find answers to common printing problems or seek advice from our members on your printer queries. If I print from themanual feed tray I get the same 13 Paper Jam error with thepaper not making it into the fuser.I recently replaced the heat lamp in the fuser Hp Laserjet 5m When it's completely dry, put it back in place and retry printing.

Welcome to the Printer Forums where you can ask questions or find solutions to printing problems. Hp Laserjet 4 Pickup Roller I noticed that the one flag moves freely and changes position with how the printer is positioned or oriented. by dmzcompute on Dec 10, 2005 at 12:55pm Add comment Please sign in to comment Thanks dmzcompute - hopefully Moe will have the gear.

Of course there was no paper jam.

However, with the fuser assembly in place and screwed down, I noticed that the flag sensor would not move freely. Asout to the edge of where the toner drum is. BD "Dewaine" <> wrote in message news:... > Where is teh leading edge of the paper when it jammed? I used some light weight lubricant and now it seems to work consistently.

Hp Laserjet 4 Pickup Roller

I have these possible leads from another site, but I need to know where to begin. 1. useful source The printer exhibits the same exact symptom. Hp Laserjet 4 Paper Jam 13 I've given the printer a once over as much as I can and following instructions found on the web, but I'm running into some problems since I don't really know what Hp Laserjet 4p Paper Jam by headknocker on Dec 9, 2005 at 2:48pm Add comment Please sign in to comment 0 If the exit rollers are not turning and the paper does not make it into

No, create an account now. navigate here Make sure that sensor arm is moving freely. > > > > 1). by dmzcompute on Jul 18, 2006 at 6:39pm Add comment Please sign in to comment 0 The fuser exit sensor is actually not on the fuser but on top of the Can you print normally from the multipurpose tray? 0 LVL 21 Overall: Level 21 Printers and Scanners 8 Message Expert Comment by:briancassin2000-02-07 1. Hp Laserjet 4 Fuser

Can you hear the roller turning? The > > rollers pick up the paper, but ir goes in about half way and stops. Join the community of 500,000 technology professionals and ask your questions. Check This Out If paper scrunches up inside by the toner cartridge in a HP LaserJet IIP, IIP+ or IIIP please contact HP Technical support.

Ensure there is no obstruction in the path, such as a torn piece of paper. 5. You also may want to get out the directions you received with the new lamp, disassemble the fuser again and make sure you replaced all the parts correctly as that roller If you have completed all the preceding steps and are still experiencing a problem, service the product.

If not, come back and we'll try something else.

Check sensors and flags in the paper path for proper operation. 13.0 PAPER JAM [LOCATION] A non-specific paper jam occurred. 1. Clear the jam and close the top door. 2. So, as an experiment, I propped the printer back with 1/2" shims to see if I could prevent the issue from occurring. If it feeds ok from the manual feed, then you'll need to replace the PIU.

ValstarPrinters 235,851 views 3:52 Fixing a Paper Jam - HP LaserJet 1020 Printer - Duration: 6:54. I bought it because it was so dependable back when I used it everyday at the office. It could also be the sensor itself which is on a board with another sensor attached to the PIU unit. this contact form If the message persists after all jams have been cleared, a sensor or sensor lever might be stuck or broken.

Try this! 144 comments How to Reset Purge Counter on a Brother Printer (Without Numerical Pad) 222 comments Clearing the Canon Pixma E04, E05, E14 or E15 Error Message 34 comments On your video I believe it used the phrase "rebuilding the exit assembly". Sign Up Login Add Question unknown asked Jul 16, 2006 at 6:36pm 0 HP DeskJet Plus HP Laserjet 4 Plus- Error 13-False Paper Jam Hello,When my Laserjet 4 Plus prints, when I can't remember where I found the suggestion, but someone mentioned that a way to fix a problem with the exit rollers was to lightly sand the lower roller.

Use a flash light and check under the oblique rollers but if the paper pass them, kind of doubt it. 4). Show more Language: English Content location: United States Restricted Mode: Off History Help Loading... If it jam before > it > > reachs the Fuser, there is a sensor under the toner cartridge. Figure 4: Lift the jam-access cover Gently pull out any jammed paper from the ADF.

This error is caused by a defective paper control PCA Replace the paper control PCA 13.2 PAPER JAM OPEN INPUT TRAYS Paper-stopped jam at paper-feed area. 1. Transfer roller guide not seated. > > > > > > Any ideas would be greatly appreciated. > > > > > > BD > > > > Dave, Aug I bought a fuser and a new toner. Do not use paper or envelopes that are bent, torn, dusty, damp, wrinkled, curled, or that do not lie flat.

i checked the "flags" that operate that sensor.just want to be sure it's the only sensor that can cause that error. Stuck or broken flags or sensors. > 3. Remove jammed media from the specified location. 2. Posted on 2000-02-06 Printers and Scanners 1 Verified Solution 4 Comments 2,128 Views Last Modified: 2013-12-15 My HP Laserjet 4 Plus is showing an error 13 Paper Jam, with no paper

Inspect and/or replace the feed and separation rollers. 4. Comment Submit Your Comment By clicking you are agreeing to Experts Exchange's Terms of Use. NOTE: HP recommends connecting the printer power cord directly to the wall outlet. Sign in to make your opinion count.