Home > Hp Laserjet > Hp Laserjet 4 22 Par Io Error

Hp Laserjet 4 22 Par Io Error

If the error is still present: 1. Replace the DC Controller. 61.[x] SERVICE X=0 - 4 The printer encountered a parity error when accessing the RAM memory SIMM in slot "X". My question is,is my file getting corrupted as it comes through Samba, or is this a UNIX systemproblem and do I need to look elsewhere?I hope this is enough information. On the HP IIIP the page count is given on the test page and on the Apple Personal Laserwriter it's on the start up page (except the LS). http://permamatrix.net/hp-laserjet/hp-laserjet-error-10-10-00.html

If serial the wrong pacing option is selected. ERROR 80 80X.YYYY ALL Printers The EIO card in slot X has encountered a critical error -power cycle, reseat card then replace card if needed. Advertisement Recent Posts Attention! A buildup of toner on the edges of the tray which slide into the printer can sometimes cause problems.

Then press the "FORM FEED" key and then the "ENTER" key. Replace or clean as needed. Bad drive gears. Replacing this should solve your problem.

Printer service error - no further operation possible until problem resolved. Replace main motor. explicit C(): suggestion of meaningful (and easy) extension 7. 22 par 10 error? 8. In some instances, electrical noise in the cable can corrupt data during transmission to the printer.

Any help here would be appreciated too. If the lamp begins to heat (you can feel the roller, but be very careful it's HOT ) its not the lamp or the thermal fuse and is most likely the Error 79 Software/drivers, Memory PCA's, Font-Macro-Personality Cartridges, option I/O Cards. To remove this assembly, remove the five brass colored screws.

Yes, my password is: Forgot your password? Take a sharp tool, like a razor blade and scrape the buildup off these edges. If the error persists, replace the Formatter PCA. 68 ERROR Nonvolatile memory (NVRAM) error. Three settings exist for the IO buffer; AUTO (default), ON and OFF.

Also, go here for the latest drivers from HP. Remove the card and reseat it, try swapping with a know good card from another printer. ERROR 51 - Service Improperly seated toner cartridge - remove and reinstall Laser shutter blocked or damaged Damaged fiber optic cable Defective Laser PCA - replace I/IID/III/IIID Defective toner cartridge - Power cycle the printer.

The media that is loaded does not match the settings of the paper tray. http://permamatrix.net/hp-laserjet/hp-laserjet-5m-53-12-03-error.html Hewlett Packard has become the leader in HP printer errors and the numbering system due to the dominant printer installation base they have throughout the world. If your running a network card in the printer try pinging the card. Top HP 4 Plus 22 PAR IO Error by Bob Guthri » Wed, 05 Jul 2000 04:00:00 The HP Quick Reference Guide gives the following: All Printers: I/O Config on the

Defective High Voltage power supply or on the LJ II/III the DC controller to High Voltage power supply can be defective. Check your printer paper setting on the printer make sure they match. do you still have the driver floppy/cd for the 4+? http://permamatrix.net/hp-laserjet/hp-laserjet-error-19-1.html Be careful with labels, use only labels designed to take the heat generated by the fuser assembly.

Press isrnii + ICWffTfflWB to clear the error message (data will be lost). You may now slide the lamp out of the fuser assembly. Also check motor cable connections.

We have found it is highly beneficial to replace the wire harness assembly and fiber optic cable when replacing the scanner since by this time you have probably already tried tweaking

Back back to top How did we do? A broken tooth on one gear is all it takes. Or the cartridge is bad. Message Description Recommended Action 70 or 71 ERROR A language (personality) SIMM problem was identified.

Error 24 Job Memory Full The print job is too complex to be processed. All Other Manufacturer's -- Select Manufacturer -- Brother Printer Supplies Canon Printer Supplies Dell Printer Supplies Lexmark Printer Supplies Okidata Printer Supplies Samsung Printer Supplies Xerox Printer Supplies Epson Printer Supplies Also on the 4V/4MV check the door open sensor (PS402) on the terminal board located under the transfer roller. this contact form Watch the termination's on the network cabling.

However, the number displayed will point you in the right direction. Only registered users and moderators may post messages here. Is the computer on?! And doggone it, People like me!

A 25 wire parallel. If the problem continues, remove the optional interface card and set the printer for standard parallel interface by taking off-line and holding down "Menu" key for 5-10 seconds. Paper Tray is overfull 2. You need to check the configuration of your printer and drivers, reset the printer, try issuing an initialization command from within the application.

How about the I/O port - damaged, seated properly, pins not bent? 4+/5P/5 The computer and printer aren't talking because of improper signal protocols. Verify that the tabs aren't damaged and that the tray switches located in the printer are not damaged. Check the connectors on the DC controller and power supply. ERROR 14 - No EP Cartridge or No Toner Cartridges No toner cartridge or cartridge not fully seated - pull it out and install it again.

MIO Configuration: This is an I/O buffer overrun error. What does this mean? Check cabling between Main Motor and DC Controller PCA. 2. Error 18 MIO Not Ready The printer is not connected to a LAN when it's expecting to see a LAN.

Another clue can be a "clicking" sound just prior to the error 50 appearing. Press isrnii + ffiWflfflnWB and the page containing the error will automatically be reprinted. Replace device which triggers error. If open, the fuser ceramic heating element will need to be replaced.

Replace DC Controller PCA. 57 SERVICE Main motor failure. I have just recently replaced both pc's that were attached to each printer.