Hp Laserjet 2200d Duplexer Error
top 49.XXXX PRINTER ERROR To continue turn the printer off then on Description The printing operation has been aborted. Printing can continue, but behave unexpected in response to the changed settings. either leave it clean or attach something to dampen the solenoid 'click'...I used a small piece of electrical tape, but it wasn't necessary.5. I tried disconnecting the electric and computer cable and shutting off the printer and holding the GO button but nothing helps. http://permamatrix.net/hp-laserjet/hp-laserjet-2200d-all-three-lights-on.html
We can not see it. If the above action does not solve the issue, contact HP or an authorized service provider. CAUTION: Ensure that all jammed paper is removed before closing the cover or tray. I lubed the motor using the great description on the link and all is well. http://www.fixyourownprinter.com/posts/15241
CAUTION: Do not fan the paper. There are more selenoids, but they are on any additional trays you may have so I have absolutly no idea what you did and anyone else who reads this will not Size isn't really critical, and it will work fine without it. Wird verarbeitet...
Hold the DIMM with your fingers against the side edges and thumbs against the back edge. Action Turn the printer power off. Learn more You're viewing YouTube in German. It looks like a section (1/4) of the gears are separated from the shaft to allow it to be flexible maybe?
apart and lubricating the motor. And when I push it there was paper under. If it does, then press the engine test button towards the back on the right side and if it prints out a page with lines, then the formatter is the issue. X Description 1- Low fuser temperature 2- Fuser warm-up service 3- Fuser over temperature 4- Line voltage problem 5- Incorrect fuser is installed 6- Open fuser circuit Action Turn the printer
Replace a DIMM or EIO device if it is the one that has caused the error. Clicking Here If the problem persists, contact HP Customer Support. The red light is on also the two green lights are on (fatal error). Später erinnern Jetzt lesen Datenschutzhinweis für YouTube, ein Google-Unternehmen Navigation überspringen DEHochladenAnmeldenSuchen Wird geladen...
Transkript Das interaktive Transkript konnte nicht geladen werden. http://permamatrix.net/hp-laserjet/hp-laserjet-4l-error.html top 50.X FUSER ERROR For help press ? Fun stuff! Pressing GO will Set the Ready led to GREEN from Blinking Attention, start the motors, but the paper pick-up mechanisms do not activate, either the paper tray or the manual feeder.
Did cleaning the engine make the problem worse? One mentioned that the 2000 series laserjet are notorious for having printer jams with duplex. If the motor is frozen these instructions should help. http://permamatrix.net/hp-laserjet/hp-laserjet-4-plus-error-51.html An easy fix! - Dauer: 7:47 maximpulse 391.294 Aufrufe 7:47 HP LaserJet 2300 Series Paper Jam Fix - Dauer: 5:59 BulkDriver.com 2.303 Aufrufe 5:59 HP LASERJET SERVICE IN 5 MINUTES -
Open the rear door of the stapler/stacker (jam-access door). Action If the incorrect size was selected, cancel the job or press the Help (?) button to gain access to help. If solid then press both buttons and report the light pattern and someone will tell you what is wrong. - dmzcompute 0 I have a HP Laserjet 2200D that when you
X Description 0- Scanner error 1- Scanner startup error 2- Scanner rotation error Action Press the (Select) button to continue.
Your cache administrator is webmaster. If this workaround is not acceptable or the error message persists after performing all of the recommended actions, contact an authorized HP Service or Support Provider: http://www.hp.com/go/support top 11.XX Internal Clock If you go to hp and click on the 2200 all that is shown is the tray 1 pad. and that piece actually triggered the paper jam. Does paper jam when exiting the printer? "Yes" 1.
If the error persists contact HP or an authorized service provider. huh! There is not duplex selenoid so I have no idea what part your cleaned the foam from. this contact form Figure 47: Removing the cover Open the DIMM-access door by pulling on the metal tab.
The line voltage and current source at the printer location might need to be inspected to ensure that it meets the printer’s electrical specifications. If the above action does not solve the issue, contact HP, or contact an authorized service provider. Most common is the formatter. In addition, the printer displays warning messages, error messages, and critical error messages.
Turn the printer off and then turn the printer power on. If the noise starts shortly after you send the print command and continues for a little while after the paper comes out, that's the scanner motor bearings.