Home > Hp Error > Hp Error Code 55.a

Hp Error Code 55.a

Technical Forums Copier Technical Discussion Canon Konica Minolta Kyocera Mita, Copystar Muratec Panasonic Ricoh, Savin, Gestetner, Lanier Sharp Samsung Toshiba Xerox Other Copier Brands Fax & Printer Technical Discussion Brother Canon If that works go back to the first application and try printing a different file to determine if the problem is file related. Check the feed and separation rollers in the printer and in the tray. Reseat the connectors between the DC controller PCA and the formatter. 4. Source

That has been known to fix odd paper handling issues for this machine but the exchange formatter should do the same thing. Verify that there is no issue with the site power. Check the cabling to the ECU. It typically indicates a communication error between the formatter and the DC controller. http://www.advancedlaser-hp-error-codes.com/error_55.htm

How did we do? Any help here would be appreciated too. Thank you and your firm again, you were terrific. Defective dc controller. 4.

Remove any expansion memory and additional USB devices and see if the fault clears. Also on the 4V/4MV check the door open sensor (PS402) on the terminal board located under the transfer roller. We might expect bad mains to also trigger 50.2 and 50.3 errors so if those are also in the error log that would be a hint. Check the printer’s configuration. 3.

Also, can I get some instructions on putting in the rollers. Pls somebody help! We got it this morning and I have it installed. http://www.fixyourownprinter.com/posts/9419 Replace device which triggers error.

If the error clears, then, the duplexer PCA may be defective. Defective main motor. Replace if problem persists IIIP/IIP/IIP+ Paper feed problem - check feed/pickup rollers for movement and wear. fixyourownprinter HP P3005 Formatter card problems - so not directly relevant to the query.

Check the power at the customer’s location. 2. A buildup of toner on the edges of the tray which slide into the printer can sometimes cause problems. If the error returns after doing this, then, check external printer connections. Also check motor cable connections.

Sometimes you can clean a pickup roller and get a little more life miles out of them but when you start to get jams with a smudge on the top middle this contact form Some pictures derived from HP User and Service guides. The page containing the error will automatically be reprinted. 2. Replace or clean as needed.

First firmware DIMM, then Formatter, then Engine PWB. Also, an new duplex-unit will not work with an old-type fusing unit. ERROR 49.XXXX A critical firmware error has occurred that caused the processor on the formatter to abort the operation. have a peek here The code 55.A will appear when the fuser and duplex can't work with eachother.

Results 1 to 8 of 8 Thread: HP 4050T 55.A Error Thread Tools Show Printable Version Email this Page… Subscribe to this Thread… Display Linear Mode Switch to Hybrid Mode Switch Add Stickiness To Your Site By Linking To This Professionally Managed Technical Forum.Just copy and paste the BBCode HTML Markdown MediaWiki reStructuredText code below into your site. HP Printers Forum Values of X, Y, and ZZ are as follows: X = DIMM type 0 = ROM 1 = RAM Y = Device location 0 = internal memory (ROM or RAM) 1

By joining you are opting in to receive e-mail.

If the printer is close to the 350,000-page service interval, then install a maintenance kit.If the service interval is not near the 350,000-page interval, then, replace the fuser. Replace this as an assembly. Make page less complex and retry. It can also be caused by a defective DC controller.

Thank you for the speedy shipment and response. The line voltage and current source at the printer location might need to be inspected to ensure that it meets the printer’s electrical specifications. 55.xx PRINTER ERROR alternates with CYCLE POWER ERROR 14 No EP Cartridge or No Toner Cartridge No toner cartridge or cartridge not fully seated - pull it out and install it again. Check This Out Remove and reinstall the supply, replace the supply.

Turn the printer off and then turn the printer on again.3. Defective laser scanner assembly. Improper MIO connection - look at pins on formatter MIO connection reseat card. Error 10.32.00 Unauthorized Supply Alternates with for help press "?" - A new non-HP supply has been installed this message continues until you press the check button or install an HP

b) Reseat any memory DIMMs and EIO cards. Back back to top How did we do? The error 10 indicates a problem with the printer obtaining the information from this chip. Printing preferences>layout>print on both sides>flip on long/short edge -- selecting either edge still does not give duplex printing.

Power cycle the printer. Bad tray bin reports.5. If not replace the motor or drive circuit as required. Error 21 Print Overrun The print job is to complex.

I truly appreciate it. Defective formatter board. 3. Improperly fitted connectors. 2. Watch the termination's on the network cabling.

Red Flag This Post Please let us know here why this post is inappropriate. We sell maintenance kits, fuser, repair parts and supplies.

Error Codes Error 10 - Supplies Memory Error 10.XX.YY Exact format is dependent on printer model The printer is unable to Turn off and turn on the printer, and see if the error clears. I will have purchasing call in an order.

Remove all EIO devices and firmware DIMM if installed. You may have to register before you can post: click the register link above to proceed. If the software tells the printer to expect a different size (legal, A4, COM10) than the tray available, you will get an error.