Home > Hp Error > Hp Error Code 49.ff04

Hp Error Code 49.ff04

Known Issues There seem to be two main error codes for the P4014 series: 49.ff04 49.4C02 usually implies corrupt firmware If the number after 49 changes there are suggestions that implies The printer is expected to provide fonts, scaling them as required but download them if a good match isn't available and to do this at 60 pages per minute with network The printer froze at 20 percent. HP have "Service Advisory" notes on the subject. have a peek here

No use to me. No datasheet available... Followers My Blog List Computer Geeks Recovering deleted files on Windows PC Picture Window template. Show more Language: English Content location: United States Restricted Mode: Off History Help Loading... http://h30434.www3.hp.com/t5/Inkjet-Printing/LaserJet-4025-CP4025-Device-Failure-error-49-ff04/td-p/5094796

Try to check the printspooler next time a 49 error appears to see what document type is being printed. Defective RAM will record bytes incorrectly at the damaged locations. Just tryin to help. - akuma6099 0 350F at 8 minutes works just fine. Press(Down Arrow) button once.

Power the printer On and verify it reaches a READY status. This type of error can be caused by invalid print commands, corrupt data, or invalid operations. The firmware for the HP LaserJet device and accessories are matched for optimal performance (certain revisions of printer firmware are tested with certain revisions of accessory firmware to assure optimal performance). In some cases, electricalnoisein the cable can corrupt data during transmission to the printer.

If the problem only occurs in one computer application that would point to it being the culprit. Printing outside the Microsoft Windows environment. If your version is older than the one on HP's site then download the top option which is the easy install version and run it on your computer. Working...

Removal is usually fairly simple, check for scratches or marks on the on the drum. If no solution is available, then most likely it may necessary to contact the vendor for resolution. A critical firmware error has occurred that caused the processor on the formatter to cease operation. Let me know.

If the error is still present with other applications or jobs, continue with the troubleshooting steps in the next section. http://www.chicagotech.net/others/printerror49.htm If you do not get the error, then it has to be the print server under Novell which is sending commands to the printer, confusing it, and causing the 49 error When the printer firmware has been successfully upgraded on its own add the accessories back one at a time. Turn the printer on.

It will need to be replaced. navigate here If you determine aDIMMorEIOdevice has caused the error,replace it. Hope this helps. Printers are tested before they are rolled out but there is no way every piece of software ever devised can be tested - or every possible sequence of events.

Turn off the printer and unplug the power cord. Quality Printers & Cartridges 721 views 3:03 How to update the firmware on your HP Printer - Duration: 3:09. NOTE: An EIO page will not print out if there is no JetDirect card installed. Check This Out Last is the formatter itself.

I'm also going to update to 08.014 and I'll try and get back here to update. A completely different driver, language and interpreter might shift the fault. Connect the printer via USB and if the printer is reconized and installs you are halfway there.

Printer specific commands are sent by PML.

The JetDirect itself is a processor which also has some firmware and that could be wrong. Paper getting stuck in thefuseris most likely caused by a badfuserwith a sticky paper sensor, heating film (sleeve) slipping or just plain worn out. The printer should boot past stage 5 and 6 of the boot progress now and not display a 49.4C02.Cancel out of the wizard setup screens. If the message persists, contact an HP- authorized service or support provider.

An example of what happens in the firmware code would be if asked to perform an action in the code like dividing by zero. HP created PCL so they are "authoritative" for it. Coming from the Network. this contact form The router was trying to hand out DHCP, this somehow killed the printers.