Home > Hp Error > Hp Error A0 27

Hp Error A0 27

If the error continues, call HP for support. Sensor Arm Stuck or Broken - check for free movement of the sensor arm. top System Error 29.3:01 Explanation Printhead Cleaner not inserted correctly in slot 4. top System Error 29.6:01 Explanation Printhead Cleaner not inserted correctly in slot 7.

Check that the printer has the latest firmware version. Recommended action Try the following: Remove the ink cartridges and check for ink leakage in the Ink Supply Station (ISS) area. This type of error can be caused by invalid print commands, corrupt data, or invalid operations. After run a Bulk Exchange command and put back the tapes the display always write errors and the Error LED lights.

Error 30 PS Error 16 ALL PRINTERS This is an unexpected PostScript firmware error. Replace main motor IIIP/IIP+/IIP Error 57-1 Incompatible memory can be either top or bottom slot. Wait 15 seconds and reconnect the power cable and turn the printer on. Recommended action Try the following: Open the printhead cleaner access door and check that the black printhead cleaner is correctly seated in slot 5 of the service station and then close

Error 18 MIO Not Ready The printer is not connected to a LAN when it's expecting to see a LAN. If the error continues, call HP for support. Check that the printer has the latest firmware version. Back back to top How did we do?

Click here for information on contacting HP support at http://h20000.www2.hp.com/bizsupport/TechSupport/CallHP.jsp?locale=en_US&docIndexId=179680&taskId=101&prodTypeId=18972&prodSeriesId=25301. Please try the request again. Add more memory. https://community.hpe.com/t5/Tape-Backup-Small-and-Medium/HP-STORAGE-WORKS-1-8-AUTOLOADER-error-code-A0/td-p/903460 May not be connected - check cabling - or it may be defective.

Any help here would be appreciated too. Error 79 Software/drivers, Memory PCA's, Font-Macro-Personality Cartridges, option I/O Cards. Power cycle the printer. Remove and reinstall the supply, replace the supply.

Replace the black ink cartridge. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=c00277456 Look for the conductive contacts on the cartridge and the corresponding contacts in the printer and make sure they are clean and free of contaminants. Click here for information on contacting HP support at http://h20000.www2.hp.com/bizsupport/TechSupport/CallHP.jsp?locale=en_US&docIndexId=179680&taskId=101&prodTypeId=18972&prodSeriesId=25301. If the problem persists, replace the Ink Cartridges.

The MIO card is defective or maybe just not seated correctly. Could be caused by a missing or misaligned cartridge carrier, an obstruction, or an unexpected cartridge in the carousel path. (http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?objectID=lpg75116)So if you are HP specialist, you could open autoloader and top System Error 85:03 Explanation Problem finding the Drive Roller zero. Recommended action Try the following: Turn the printer off (using the power switch at the back of the printer), and disconnect the power cable.

Back back to top How did we do? In some instances, electrical noise in the cable can corrupt data during transmission to the printer. sometimes it shows SCANNER ERROR 12 & sometimes SCANNER ERROR 20. If the error continues, call HP for support.

Reply 0 0 « Previous 1 2 Next » « Message Listing « Previous Topic Next Topic » Related Documents HP Printers - Using HP Diagnostic Tools for HP Printers in This pad needs to provide friction to the feeding paper. top Provide feedback Please rate the information on this page to help us improve our content.

top System Error 26.2:01 Explanation Bad contact detected in ISS slot 2 floater.

Click here for information on contacting HP support at http://h20000.www2.hp.com/bizsupport/TechSupport/CallHP.jsp?locale=en_US&docIndexId=179680&taskId=101&prodTypeId=18972&prodSeriesId=25301. Recommended action Try the following: Turn the printer off (using the power switch at the back of the printer), and disconnect the power cable. Recommended action Try the following: Turn the printer off (using the power switch at the back of the printer), and disconnect the power cable. Check that the printer has the latest firmware version.

Also check the toner level sensor and the toner cartridge itself for damage. Improperly seated SIMMs or font cartridge - remove, check/clean contacts re-install and try again. If the error continues, call HP for support. Click here for information on contacting HP support at http://h20000.www2.hp.com/bizsupport/TechSupport/CallHP.jsp?locale=en_US&docIndexId=179680&taskId=101&prodTypeId=18972&prodSeriesId=25301.