Home > Hp Error > Hp Error 58.2

Hp Error 58.2

Check the cable connection of the DC controller (J301) to the low Voltage power supply (J201). You can even send us your printer for repair. Colour laser printers have a more elaborate environment sensor incorporating a humidity gauge and seem to do more with the information. -- Copyright G & J Huskinson & MindMachine Associates Ltd The idea seems to be that the printer measures the environment temperature at startup and then estimates what the timing will be for bringing the fuser up to operating temperature.

Open the top cover and remove the toner cartridge. 2. It says 58.2 is the air-temperature sensor. That's really about all you can do as there really is  very little info about the temperature sensor in the service manual. Web Research I tried querying Google with P4015 "58.2 ERROR" in quotes (because I think that is what the printer says) and got a suggestion of 6 results all of them http://printerrepairsupport.com/58-2-printer-error-hp-4240-4250-4350/

If the fuser has achieved the correct temperature the printer goes to READY but if it is too cool it goes to 50.2 or 50.8 and if it is too hot Verify the environmental thermistor cable is securely connected. 3. The whole PIU (pickup assembly) is held in by 4 screws in the front and it slides out.

Do not apply stress to the control-panel wire-harness when rotating the top cover away from the printer. 6. This content is provided “AS IS” and is subject to change or removal at any time. Verify accessory connection. 57.X PRINTER ERROR A fan failure was detected. Replace the power supply.HP LASER PRINTER 4200, 4300, 4250, 4350 ERROR CODE 58.31.

Also, I did find another reference to the sensor that reports that it measures the outside temperature to tell the machine how long to take to warm up the fuser. It works if I dont put in the 2 screws on the right side. Improperly fitted fan cable. 2. click site The page containing the error will automatically be reprinted. 2.

A critical firmware error has occurred that caused the processor on the formatter to abort the operation HP laserjet 4250 49.24.02 error A critical firmware error has occurred that caused the Use needle-nose pliers to release the print-cartridge drive-arm. 5. Not 58.20. Thanks for any help!Bob Respond to this 0 It's in the manual.

Replace the fan.5. http://www.fixyourownprinter.com/posts/51650 Power supply error.2. A:  It is not uncommon for hp laserjet 4300 printers to loose their network connectivity especially since they were outfitted with the 615 network cards.  Try printing the network configuration settings.  Some pictures derived from HP User and Service guides.

The environment sensor in this case is just a thermistor indicating the temperature. It will be treated the same way for the above dmzcompute's solution. Disconnect the control-panel wire-harness from the DC controller PCA. If not, then you need to replace the air temperature sensor.

It then gives the fuser an adequate time and then measures it's temperature. It is not in the service manual and all the help says is power the printer off and back on. Thanks again, for all the support. Grasp the formatter cover. 2.

Printer Repair Parts, Support and Supplies Printer, copier, and fax repairs done right the first time.About MyselfContact UsBrotherHPLexmarkXeroxHome » HP Support Articles » How to Resolve the 58.2 Printer Error on Turn the printer off and then turn the printer on again.3. Replace the memory controller PCB. 5.

If there is not continuity between the fuser connectors neutral and hot with the fuser removed, replace the fuser.

Sign Up Login Add Question rhn0327 asked Oct 29, 2007 at 1:26pm 0 Unknown Printer Laserjet 4350 58.20 Error Anyone ever see a 58.20 error? Replace the power supply.HP LASER PRINTER 4200, 4300, 4250, 4350 ERROR CODE 58.21. Kevin Find additional printer service tips, manuals, and parts diagrams at: http://www.lbrty.com/resources.html/Additional Printer Repair Articles can be found at : http://www.metrofuser.com/ Related posts:51.10 Printer Error - HP Laserjet 4200, 4250, 4300, Remove the two rear mounting screws. 3.

Try the DIMM in another slot. (The firmware DIMM must remain in slot #4—the lowest DIMM slot.) 3. The thermistor leads only go through the high-voltage power supply because it acts as an interconnect from the left to right side of the printer. Respond to this 0 Good troubleshooting. 58.1 is tray one and 58.2 is tray two. It might be right.

I have read where people remove the power supply and after reinstallation they get the 58.20 - 58.2 printer  error because they forget to plug it back in.Removal Procedure of the HP RG5-5359-000CN HP Laserjet 4100 Rg5-5359 Engine Control Board MFG Part Number: RG5-5359-000CN Condition:Refurbished MFG:HP $20.00 Call for Assistance 877-755-5300 Home About Us Contact Us Search Site Map Reseat cables to the laser/ scanner and engine controller. 4. If that does not work, replace the fuser.

Replace the pick up and separation pad on tray 1.3. Replace try one input unite. Check the main motor’s cable to ensure that it is seated properly. 4. Thank you.

The service manual says it's a 58.2 printer error while several people report the error showing up as a 58.20  printer error. HP LASER PRINTERS 1200, 2200, 3100, 3200, 4100 1. A:  A 50.1 fuser error with the laserjet 4300 printers is a common error and simply means that there was a problem with what is called the fuser assembly.   The hp HP LASERJET 4300 ERROR 50.1 Q:  Our hp laserjet 4300 has a fuser error 50.1 on the display panel.  The printer was running fine the day before and the next morning

Replace the D.C.