Home > Hp Error > Hp Error 54.6

Hp Error 54.6

Reseat all toner cartridges and make sure the toner lock lever is fully locked on all toners.3. Compare the settings in this dialog box with the ideal settings in your printer's manual. Lift the registration flap and verify that the OHT sensor is not blocked. 3. Replace the print cartridge. 6.

Got it, continue to print 2012-2016 ManualsLib.com About Us About ManualsLib Privacy Policy F.A.Q. The toner cartridge drum does not have any toner deposited. Indicates a density sensor error/2. You can add, delete list items and change the quantity of spare parts.

Your cache administrator is webmaster. Remove JetDirect card before resetting to preserve settings. I had a transfer kit available, so I replaced the transfer items. These levers, used to help remove fuser jams, should be in the position which applies pressure to the media as it passes between the rollers.

Slide the drawer back until the second set of rollers align with the opening in the rail and lift the drawer up and out. by jdwvw on Jun 23, 2005 at 8:06pm Add comment Please sign in to comment 0 Just a thought, sometimes when the separation roller for tray 2 slips it makes a I suggest posting in the forum for HP Business Support as well for yet a better chance at finding a prompt solution.You may find the commercial Laserjet board here.http://h30499.www3.hp.com/t5/Printers-LaserJet/bd-p/bsc-413Best of luck;RobertoR Updating or installing a new driver won't solve every printer woe, of course, so understanding Windows' built-in Help system will give you an even sharper troubleshooting edge or get a on/off

Replace the ECU. Make sure it is not broken and swings freely. Lift the registration flap and verify that the OHTsensor is not blocked.3. https://www.orionmarket.com/product_error/8529/HP/HP-4550/54.6-printer-error/ back to top How did we do? •HP LaserJet 8150 Error 50.1 Fuser Error We have found this to be the low voltage power supply, part number RG5-4357.

If the motherboard ... First Time Here? Open the ITB drawer and remove the transfer belt assembly. EN Control panel messages 31 1 Previous page Next page 1...333435363738394041 Also See for HP Color LaserJet 4500 HP Color LaserJet 4550 Quick Reference Service Manual 220 pages HP Color

Replace the high-voltage power supply HP COLOR LASER PRINTER 4500, 4550 ERROR 54.21. check here If the error persists, verify that all connectorsare firmly seated.5. I will have purchasing call in an order. Restore password × Upload manual upload from disk upload from url Thank you for your help!

The connector is located on left rear of ITB drawer and the corresponding mating connector is on the chassis. This cleared the 54.6 errors, but now I get a 13.11 paper jam error with the same noises and paper jam location from tray 2. If the error persists, verify that all connectors are firmly seated. 5. Remove the ITB and verify that the OHT sensor prism is in place. 2.

HP LASER PRINTER 8500, 8550 ERROR 54.2 1. Turn the printer off and then on again. 3. Sign up! Pull the drawer out until it reaches the stops.

You will have to remove the cover, the control board cover, fuser, and a few other items to gain access. Usually related to toner and print cartridge sensor problems. 2. Action, the service manual says: 1-open and close door, 2-reseat cartridges, 3-check contacts to transfer unit, clean if dirty, or replace transfer unit if they cannot be cleaned or are damaged,

How to fix Motherboard problems Since all computer components are connected on the motherboard, motherboard failures can be difficult to troubleshoot.

Click Printers and Other Hardware and Printers And Faxes. The lever is on the opposite side of the fuser as you face the printer from the edge that is not fusing. You can download printer drivers from the printer manufacturer's Web site. Get more help. Replace the waste toner sensor ass'y3.

Part# RC1-1247-000 - Lever, ITB Coupling, It's the same part for HP Color LaserJet 3500 and 3700. Remove the printer from any UPS supplies, additional power supplies, or power strip. Main motor defect. controller.

See Figure 7-24 for the sensor locations. This problem occurs with tranfer belt serial numbers earlier than lot EHC5001064 The lot code is located on the white barcode label on top of the tranfer belt. by dmzcompute on Jun 23, 2005 at 2:02pm Add comment Please sign in to comment 0 These printers are prone to toner bombs. Privacy Policy Terms of Use Discussion Boards Open Menu Discussion Boards Open Menu Welcome to the Forum!

In the Printers And Faxes window, from the File menu, click Server Properties, then click the Drivers tab. Order part number CLIP4200R for this repair. Error code Error 13 or Error 54.6 Problem: " Reinstall Transfer Belt " error message Possible Causes and Solutions This can be caused by debris or paper scraps blocking connector pins If the message persists, check the sensors in the priner to verify that they are working correctly.

You can download printer drivers from the printer manufacturer's Web site.Get more help. Indicates that the temperature/humidity sensor has malfunctioned.2. We got it this morning and I have it installed. Any suggestions before I call for service would be appreciated...

Remove all toner cartridges and reseat and check for obstruction.3. Waste toner sensor has failed.2. The resulting page is generally black and tends to curl from the excessive toner fusing to the page. Remove ITB and verify that the OHT sensorprism is in place.2.

What Our Users Say Press & Media Contacts Advertising DMCA Policy Brands × Login Login to ManualsLib Don't have an account? Turn the device off and then turn the device on. 3.