Home > Hp Error > Hp Error 50.xx

Hp Error 50.xx

HP LASER PRINTER 20151. Plug the printer into a wall outlet and see if this resolves the problem. 3. X Description 1 - low fuser temperature 2 - fuser warm up service 3 - high fuser temperature, fuser over temperature 4 - faulty fuser 5 - Incorrect fuser installed 6 HP laserjet 4000 13.XX PAPER JAM - Paper is jammed at the specified location (and possibly at other locations) HP 4000 13.1 PAPER JAM OR 13.2 PAPER JAM Paper delay jam

Bad low voltage power supply5. A fuser error has occurred.2. After verifying the problem is related to the AC power supply, check the fuser for common wear and tear in case the fuser also needs to be replaced. To check the fuser, turn the printer off and remove the fuser. http://www.printertechs.com/printer-troubleshooting/hp-error-codes/195-numeric-error-codes-50-59-hp-laserjet

if the message persists, replace the fuser assembly. Verify that the correct voltage fuser is installed. 5. System error 43:11 The Vacuum fan is not detected. The DIMM that caused the error will not be used.

Step three: Verify the paper type Verify that the paper type selected matches the type being used in the printer. Washington) 91343 Los Angeles (North Hills) 91601 Los Angeles (North Hollywood) 91602 Los Angeles 91603 Los Angeles 91604 Los Angeles 91607 Los Angeles 91324 Los Angeles (Northridge) 91325 Los Angeles 90272 HP 500 System error 01:11 The electronics module has detected a connection problem with the cooling fan. Figure 2: Open the upper right door Locate the fuser.

check the cable connections between the ECU and the fuser. 10. Turn the printer off and allow it to cool down.2. System error 21:10 A problem has been detected with the Service Station assembly. http://www.all-laser.com/a50service/ Remove 7 screws Note: Make sure you remove the LVPS fan from the unit and put it on the new one before installing back in your machine.

We help people fix printers. Turn the MFP off, and allow it to cool. 3. San Rafael, CA Great that you have that part in stock and thank you for your quick reply. At room temperature, you should read in the range of 50Kohms to 350Kohms at room temperature.

The printer has experienced an internal hardware error. 2. https://www.orionmarket.com/product_error/3013/HP/HP-4345/50.x-fuser-error/ Defective fuser.3. The page containing the error will automatically be reprinted. Replace the power supply5.

If you experience any of the above issues with the fuser replacement it (RG5-6532) along with the power supply. The page containing the error will automatically be reprinted. 2. Defective fuser and AC power supply 3. Replace the environmental thermistor.

The line voltage and current source at the printer location might need to be inspected to ensure that it meets the printerís electrical specifications. 50.X FUSER ERROR A fuser error has Inspect the fusing assembly connectors, at the front of the assembly, and the connectors on the high-voltage power supply PCA. Power cycle the product to determine if the error is persistent. 2. The gears should rotate smoothly.

System error 56:10 Drive roller encoder sensor error. We recommend the following procedure to manually set the maintenance count to zero. The page containing the error will automatically be reprinted.

Power supply is the most common cause. (RG5-4357) Pull the fuser out and check the thermal fuse on top of the fuser and the lamps inside the unit for continuity to

Remove 2 screws and remove housing. If that does not work, replace the fuser. HP DJ 500 System error 01:13 A problem with the Electronics module has occurred. Replace the DIMM that caused the error. 54.1 REMOVE SEALING TAPE alternates with FROM TONER CARTRIDGE The toner cartridge has been installed without removing the sealing tape. 1.

Bad D.C. Replace power supply 50.4 Fuser Error Description: faulty fuser - fuser assembly is experiencing a defect withing the assembly circuits. When checking the fuser: Check the middle of the hot roller for toner build up that could cause ghosting or poor print quality. Hold down the Item key (minus side of the button) and Value key (minus side). 3.

Check the main motor’s cable to ensure that it is seated properly. 4. HP LASER PRINTERS 3SI, 4SI 1.Temporary error code. Error Code 13, 13.1, 13.2, 13.3 Paper Jam/Paper Jams 13.20 error code paper jam or bad paper feed drive assembly. Step five: Reseat the fuser Turn the printer off.

On older style printers this is often caused by a bad main motor. (Older style printer being printers with halogen heating elements in the fuser - 4, 4+, 5, 4si, 5si, Replace the power supply board. System error 21:11 A problem has been detected with the Service Station assembly. Works great and certainly solved the problem (as I expected it would). -Alan A.

HP LASER PRINTER 4345MFP, 5025MFP, 5035MFP ERROR 50.X FUSER ERROR 1. back to top Home | contact Us | About Us | Terms of Sale | FAQ | HP Maintenance Kits | HP Fuser Assemblies | HP Color Supplies |HP Parts The page containing the error will automatically be reprinted. Turn the printer off, and then turn the printer on. 2.

Open the top cover door, and remove 2 screw 3. Defective fuser. 3. Verify fuser part number with proper HP Printer model.  3. Verify that the correct voltage fuser is installed..  4. Replace Fusing Assembly with correct fuser assembly. 50.6 Fuser Error Description: open fuser circuit Solution: After installing a maintenance kit, reset the maintenance count to zero by: 1.

Make sure that you put the correct model fuser in the right printer. Verify that the correct voltage fuser is installed in the product. 4. If the error persists, replace the fusing assembly. 8.