Home > Hp Error > Hp Error 13.03.00

Hp Error 13.03.00

If the rollers have just been replaced and start giving this error they might not be seated correctly. Tray 2 13.03.00 JAM IN TRAY 2. Users commonly become aware of a problem when they see an error code. If they are lost then either equivalents will have to be found in a junk box or the paper feed shaft will need replacing, which is difficult to do and therefore

by moe on Jan 4, 2013 at 9:48am Add comment Please sign in to comment 0 This location i'm working at has envelope feeders on nearly every printer they have. CAUTION The PIU is heavy. 12 Grasp the PIU  handle, and lift the PIU out. Change the contents of the old list and save it as new. Once I pulled it out and started looking through the gears on the side, I noticed nothing was driving the two sets of grey feed rollers the pull the paper up http://fixyourownprinter.com/posts/52594

If there is a visible paper-jam in tray 2 note where it is and clear it. A:  Hp 4200 printers that crumple, crunch, crease the page are very common.  The fact that the print is smudged on the page leads me to believe that it is probably Check the delivery sensor PS700 using diagnostics. 13.20 JAM INSIDE Duplexer - Remove the duplexer by lifting and pulling it from the rear of the printer.

Die Bewertungsfunktion ist nach Ausleihen des Videos verfügbar. Wiedergabeliste Warteschlange __count__/__total__ How to fix 13.02 and 13.03 Paper jam Errors; HP laser Jet P3015 Series Printer Izzy Kilman AbonnierenAbonniertAbo beenden4444 Wird geladen... Anmelden 1 Wird geladen... Respond to this 0 A 13.03.00 error message indicates that the media did not arrive at the top-of-page sensor (PS103) within the specified time.Have you tried swapping the tray 1 feed

It isn't directly the envelope feeder... Listen for the audible click of the solenoid and clutch. Open the trays, check for misfeeds, then check the trays are properly closed. laserzone123 Copy of chapter 7 of the HP manual "Solve Problems" fortwayneprinterrepairpushing his article again via another forum - but there were several other fairly interesting articles so it's still useful.

It is unlikely (although not impossible) that all the rollers on a printer will be equally worn out. Recover the cog, spring and e-ring from the tray or floor nearby if possible - they are not available as HP spares. All the points so far can easily be checked by a user. There is a matching roller in the body of the printer which will be equally worn.

Something is stuck in the paper path as a result of a previous jam The pickup and feed rollers are damaged or worn out and need to be replaced. "13" errors but i'm guessing it is part of the issue. If the paper seems wedged in there, take the cartridge out and pull and push the page up to the registration station; avoid pulling paper backwards; the paper path was not The Diagnostics menu can test the tray 1: paper sensor - which should change an indicator on the display when it is pressed solenoid which should make an audible click when

Although 69 results were suggested the remainder were all similar. This blog is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking If you have difficulty, use needle-nose pliers. 4 Disconnect the four locator tabs  on the cable cover, and then remove the cable cover. 5 Unplug two multiple-wire cable connectors. Unfortunately this machine was in the middle of a factory and it was very loud so it was hard to tell what was making the noise.

See the catalogue. Constantly got the same error. It is usually the most heavily used paper-feed tray in a printer. Make sure not to scrape the top of the registration assembly against the chassis.

Changing the clutch is a major job, so perfectly good printers could be going to scrap for want of £15 worth of rollers. Dirty/hot environment. Frequent jams in the fuser area implies something wrong.

Nächstes Video Phantom Paper Jam Nightmares With The HP LaserJet Enterprise P3015 P3015dn Laser Printer - Dauer: 17:42 HSM IT Services 1.342 Aufrufe 17:42 PRINTER REPAIR: HP LaserJet Enterprise P3015 Fuser

Melde dich bei YouTube an, damit dein Feedback gezählt wird. For what its worth I've put "nofollow" on the spammy links above because I see no need to promote them further. Paper sticks to the stack it was supplied in, separates but feeds skewed, or the electrostatic fields inside the printer attract it unduly and it collides with something or even wraps Seed material for a forum with no user comments at the present time.

Users are not very friendly to this device. Create your Spare Parts List. Remove the misfed paper. Like some of their machinery.

If you've tried other trays, then it's going to be some kind of communication/settings problem since the printer works fine without that envelope feeder, unless I'm reading it wrong. There are several points here: Higher positions in search can be gained by a variety of messages on forums all linking to a page; its an old trick and it still New service manuals Samsung SLM4020ND, (sm, pc), Eng, 26.8Mb Canon MF515x, (sm, pc), Eng, 33.4Mb HP LaserJet M506dn Enterprise, (srm, stm, pc), Eng, 46.1Mb HP LaserJet M403dn Pro, (stm), Eng, 4.87Mb Paper jams can be caused by poor-quality paper or material that is out of specification, failure of the motor or sensors and things jammed in the paper path.

Do a manual sensor test. Open the cassette tray mentioned in the message and look at the roller in the front centre (tray 2 is the built in cassette). Wird geladen... Solution: 1 Press ? ( HELP button) for detailed information about clearing the jam. 2 Press ( UP ARROW button) and (DOWN ARROW button) to step through the instructions. 3 Check

So I then removed the registration assembly.