Home > Hp Error > Hp Error 020011

Hp Error 020011

System error 060200 Explanation Incompatibility between Firmware A.01.07 and the new Carriage PCA. Firmware - first slot, PS - second slot, Memory SIMM's - third and fourth slots (left-most slot is slot one, when looking from the back of the printer). System error 020000 Explanation Error in finding the primer home position. Remove and reinstall as needed.

Replace Electronics Module. If the error reappears, contact HP support. If the error reappears, contact HP support. Perform Carriage Calibration. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-c00010030

System Error: 010038 - Refer to error code "010037' : System Error: 010039 - Check/replace Trailing Cable. top System error 060000 Explanation The line sensor is not functioning because there is too much ambient light. Recommended Action Turn the printer off, then on. If the error code remains after installing the latest Flash SIMM then report the error to the HP Response Center or the nearest HP Support Office, stating the following information: •

Thank you! Check that the Encoder Strip is NOT damaged or dirty. If the error reappears, contact HP support . Open the top cover.

Check Line Sensor is installed correctly. Perform the Electronics Test. Service manuals, Parts Catalogs, Error Codes, Troubleshooting, Service Menu, Adjustment, Reset Codes, Compatible Devices, Equivalents Parts and Circuits diagrams. http://support.hp.com/us-en/document/c00010030 System error 010102 Explanation The EEROM read/write operations do not match.

Ensure the MIO card in installed correctly. Following Mark encoder cleaning, turn the printer off, then on, and allow printer to initialize. When the Carriage Assembly, Refill Assembly or the Electronics Assembly is ordered, a Refill Calibration Tool, a special Carriage height gauge and an Instructions flyer will be included. Recommended Action Turn the printer off using the power switch on the back of the printer.

Recommended Action Turn the printer off, then on. http://printcopy.info/?l=en&mod=erc&brand=HP&model=DesignJet%203800CP&code=020011 If "D0809 Fail" - Check Media Sensor cable. Use Up and Down Arrow keys to select font type required and then press Enter. Replace Front Panel Assembly hp DesignJet 2500CP and 2000CP Printers Quick Reference Service Manual 9 D08.

If instructed to install the ink cartridges, install the cartridges and verify printer functionality by printing several internal prints. Perform Line Sensor Test. hp DesignJet 2500CP and 2000CP Printers Quick Reference Service Manual 1 1 D16. If "D0901 Fail" - Reseat/replace MIO card.

Replace Trailing Cable. Recommended Action Turn the printer off, then on. Replace Line Sensor. If the error reappears, or problems persist when verifying printer functionality, contact HP support.

Recommended Action Turn the printer off, then on. Recommended Action Turn the printer off, then on. Turn the printer off and remove the power cable.

If the calibration pattern is bad again, then replace the complete Ink Delivery System of the color that is bad.

If the error reappears, contact HP support. System error 020003 Explanation Error in finding the refill stepper motor home position. If the error reappears, contact HP support . If the calibration pattern is bad again, then replace the complete Ink Delivery System of the color that is bad.

If Service Station fan is faulty, check Service Station Interconnect Cable. New service manuals Samsung Xpress M2670FN, (sm, pc), Eng, 12.4Mb Canon imageCLASS MF515dw, (sm, pc), Eng, 33.4Mb HP LaserJet Enterprise M506, (srm, stm, pc), Eng, 46.1Mb HP LaserJet M501n Pro, (srm, System Error: 010021 AXXXXXXX NOTE: Printer will not function without any RAM SIMMs installed. Recommended Action Turn the printer off, then on.

C08. If the error reappears, contact HP support. Reposition tab(s) as needed. This Calibration must be used to reset the Maintenance counter to ZERO after the Preventive Maintenance Kit has been installed in order to disable the "Maintenance Advised" message on the front-panel.

If the error reappears, contact HP support. Recommended Action Turn the printer off, then on. You can print your Parts List or export to Excel to further work with him. The first time a PostScript print is sent to the printer, the other font types will be deleted and cannot be recovered.

Recommended Action Turn the printer off, then on. System Error: 060100 - Calibrate Line Sensor. See your browser's documentation for specific instructions. {} Z7_3054ICK0KGTE30AQO5O3KA30U5 hp-support-head-portlet Actions ${title} Loading... Check if the cable for the faulty sensor is connected correctly.

Check/replace the Left Door Sensor. Recommended Action Turn the printer off, then on, and retry function. Insure that at least 4 MB or memory is installed: Turn the printer off, and unplug the power cable. Replace Electronics Module.

If the carriage does not pick up the Cutter Assembly, test has failed - Check if the Cutter has been disabled through the front-panel (Device Setup / Cutter). Country: United States Select a location Americas Europe, Middle East, Africa Asia Pacific and Oceania Select a language Confirm Back Z7_M0I02JG0KOT530A6KJKFRQ0816 hp-detect-load-my-device-portlet Actions ${title} Loading... For information on solving Image Quality problems t Users Guide. If more than one RAM SIMM is installed, remove one of them and power on the printer again.

If the error reappears, contact HP support .