Hp Deskjet 5550 Blinking Ink Light
Insert the duplexer into the rear of the product, and then push it forward until it snaps into place. Even small pieces of paper can cause paper feed issues. Figure 58: Attach the rear access door and secure the door latch Method two: Clear the paper jam through the duplexer Press the Power button () to turn off the product. If you believe this post is offensive or violates the CNET Forums' Usage policies, you can report it below (this will not automatically remove the post). Source
Press the Power button () to turn the product on. Press and hold the Power button (). Checked Usb, cables,etc. This has been driving me crazy. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=c00035263
Hp Deskjet 5550 Blinking Ink Light
I do not have the knowledge in this area you have and would much appreciate any help. I had just bought another $24 blk cartridge because I couldn't eliminate the blinking light with a refill cartridge. Can someone help me on this? But, I have only tried to print in black and white.ThanksMC - Anonymous 0 Then I suspect the carriage board is failing.Unfortunately the only way to prove it is to swap
The carriage moves to the center of the product. look where the cover closes, you youl find a small piece of plastic... If the carriage is stuck in the middle of the product, move the carriage to the right side of the product. Hp Deskjet 5550 Manual If so, how do you fix it??
NOTE: Do not push the paper too far into the product. Hp 5550 Print Cartridge Status Light Is Flashing Remove any loose paper or obstructions found. It slid back into place in the service station. http://support.hp.com/us-en/document/bud09629 Step one: Clean the paper pick rollers inside the product Your product has either a rear access door or a duplexer.
Raise the cartridge latch. Hp Deskjet 5550 All Lights Blinking Nothing on HP site -- any thoughts?? there is a sensor jamed. Step four: Make sure that the carriage can move freely Press the Power button () to turn on the product.
Hp 5550 Print Cartridge Status Light Is Flashing
My daughter was having trouble printing on her iMac and we decided to try using my printer on her iMac. but it only supports 300 dpi... Hp Deskjet 5550 Blinking Ink Light Wait until the carriage stops moving and is silent before proceeding. Hp Deskjet 5550 Printer Driver It has plenty of paper!
Turn the knob on the rear access door counter clockwise, and then pull the door out to remove it. this contact form Figure 84: The Black Cartridge Problem icon Cause There is a problem with the black cartridge. Wait for the carriage to move. See the documentation that came with the HP product for more information. Hp Deskjet 5550 Troubleshooting Guide
Should I talk to HP??? Wait until the carriage stops moving and is silent before proceeding. Open the top cover. have a peek here Since I have graduated I wasn't printing so much and my spare cartridge sat around too long and got too dry to pump.
The printer refuses to pick up paper. Hp Deskjet 5550 Carriage Stuck There's all sorts of 5550 information there. How to print a self-test report Make sure that plain white paper is loaded in the input tray.
Unplug the power cord from the wall outlet.
Close the duplexer door. The product lights might flash and the carriage might move. Cancel Print / Help" )When I press the resume button on the printer, it pulls the page back slightly then spits it out blank and prints the actual document with no Hp Deskjet 5550 Won't Print by Stephen on Sep 12, 2005 at 7:43pm Add comment Please sign in to comment At Power ON, Resume and Power lights blink continuously.
and please... Press the Power button () to turn off the product. From the Type is drop-down menu, select the paper type that matches the paper in the tray. http://permamatrix.net/hp-deskjet/hp-deskjet-932c-troubleshooting-blinking-light.html Thank You so much, Nick - Anonymous 1 They don't have an infinite life.
Provide feedback Please rate the information on this page to help us improve our content. I have run the process several times and the same problem occurs. With the product turned on, disconnect the power cord from the rear of the product. Gently wiggle the spot sensor, it is sitting on top of electrical contacts and you may be able to get a better connection.
Store the paper in a dry, cool place. The product is on and ready for printing. If these steps resolved the issue, you do not need to continue troubleshooting. If you completed all the preceding steps and your product still has an issue, service the product.
Choose from the following two methods to clean the paper feed rollers through the rear access door or the duplexer. How do i know what to get. The printer has paper, there is no paper jam, ive tried with 1 sheet 10 sheets and the rest. by [emailprotected] on May 11, 2008 at 7:18pm Add comment Please sign in to comment 0 Unplug the power supply from the wall for a few minutes and then try again.If
Close the cartridge latch. Follow these steps to determine the cartridge issue, and then continue to the next section for solutions to resolve the issue. If the issue persists, continue with the next solution. pulled the paper out and it stopped printing.
Look at the drawing and then find the icon in the following figure that matches the drawing. Remove any loose paper or obstructions found. If the test page does not print, continue with the next solution.