Home > Hp Designjet > Hp Designjet 750c Plotter Printer System Error 060309

Hp Designjet 750c Plotter Printer System Error 060309

You will need that little bit of sanity over the next half hour.7. by unknown on Mar 16, 2010 at 8:47am Add comment Please sign in to comment 0 I too could use a copy of that64 bit driver. Thanks by phamsterman on Aug 17, 2010 at 7:17pm Add comment Please sign in to comment 0 SYSTEM ERROR 010060 is a Primer Motor sensor problem, Sensor might be bad, motor The diagram also shows the panel piece going from the ports whereas the back panel is one piece from the top of the plotter. (Hope that makes sense) by unknown on http://permamatrix.net/hp-designjet/hp-designjet-750c-system-error.html

Make sure that you carefully inspect the ribbon cable for bad/folded back foil contact ends. When you turn it off, the printer no longer checks the cartridges before each plot. I have tried saving my files in 2004 format but that doesnt work either. Anmelden Teilen Mehr Melden Möchtest du dieses Video melden? http://www.fixyourownprinter.com/posts/32924

Any suggestions will be helpful. Perform a Nozzle Print Test in Service Mode as described below: When the Error message is displayed on the front panel press ENTER. I forgot to mention that I had replaced the drive belt earlier as it had shreaded itself. Any suggestions...

Generated Mon, 17 Oct 2016 22:19:39 GMT by s_ac15 (squid/3.5.20) Any ideas? by unknown on May 24, 2011 at 9:45am Add comment Please sign in to comment Hi, Im a bit rusty on this machine. Turn Pen Checking to on.

Loading...Oops :Please try again. Use the ARROW button to scroll to the Utilities menu display. from Office programs?? http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-c00010030 Cant print, wont feed or cut none of the buttons seem to do anything.

by Anonymous on Dec 12, 2009 at 2:32pm Add comment Please sign in to comment Go here and follow for your model: http://www.lpscomputer.com/ec/manuals.htmI just did our 750c plus, its not too Perform the Drop Detect calibration Look for ink spray on the tape. If I press continue, it prints great. When putting the belt over the end wheels use a little piece of wood to hold the spring tensioner.Good Luck. - Anonymous I replaced the belt on my 350c about a

I cannot speak for other models.3.

I dont know if you can find the carriage anymore from a repuatable store or for a good price. by nivek on May 4, 2009 at 12:34pm Add comment Please sign in to comment 0 I HAVE A 755CM HP DESIGNJET. If you got to the user manual > Calibrations > Page 7-3 under entering the service tests menu > go to step 5 during power up.

Any suggestions? http://permamatrix.net/hp-designjet/hp-designjet-750c-plus-alignment-error.html THE VERT. I understand this will work with windows 7 Operating System. Or it was improperly seated, unseated.Paul by pbrooks259 on Jan 10, 2010 at 9:39am Add comment Please sign in to comment 0 I have a plotter hp designjet 750C, just wanna

Please help me someone!!!! Take the printer outside on a clear afternoon, have some towels, a drop cloth for the ink well, Leave it secured to the stand, if you have one, and start taking Drat - still, it might not be too late I'll email and see.Thanks again by rayat on Jul 10, 2010 at 3:32pm Add comment Please sign in to comment 0 Hi have a peek here Hewlett-Packard shall not be liable for any direct, indirect, special, incidental or consequential damages in connection with the use of this material. Web computercare.cc

If anyone could help me out in getting this thing working that would be amazing, I am currently a graphic design student and this machine could save me a lot of Or just drag it here! Anmelden Statistik 8.830 Aufrufe 5 Dieses Video gefällt dir?

Draw pictures of the connections prior to disassembling them and it will help during reassembly.

Anyway its pretty easy just open the lid and observe the two sides and you will notice where the window goes down into the cover and where the switch should be. We ultimately got beyond the message and it is working. by unknown on May 24, 2010 at 12:44pm Add comment Please sign in to comment http://forums2.itg1.itrc.hp.com - pbrooks259 0 I'm trying to print a "banner" using th roll paper, It cut's Also the black did not appear to be printing smoothly.

If no error reinstall and reconfiguire the card. You can try to get the XP 64-bit driver from someone with an XP 64-bit install CD or if you send me your email, I can send you a zip file If I believe I have a failing cartridge I always get a dry paper towel or old cloth and press it over the nozzles dont rub becuase it could scratch them http://permamatrix.net/hp-designjet/hp-designjet-750c-plus-manual.html by unknown on Mar 5, 2009 at 12:25am Add comment Please sign in to comment 0 From the front control panel message, Ready or Ready to Plot, press ENTER.Press the Up

What I do to get it to restart, when the menu shows up, start scrolling through the menu, going up AND down, only going in one direction doesn't seem to work. The old belt can be removed by cutting it if you wish. Two of the colored inks would not flow so he heated them in very worm water and that fixed it.David by Anonymous on Feb 10, 2009 at 8:21pm Add comment Please Learn more You're viewing YouTube in German.

Any suggestions? Wird verarbeitet... Ultimately you can assign a static IP, subnet, gateway address, and all that is necessary. Remove the belt from this, slide the belt out of the underside of the carriage, and carefully pull the remainder from the printer. 10.

Could this be the problem? The error is a communication error between the carriage and the main processors and the trailing cable is what provides that communication that is what I would look at first. Thanks in advance. --jf by jf62 on Jul 18, 2006 at 2:10pm Add comment Please sign in to comment The instructions for replacing the belt involve disassembling virtually the entire plotter. I have to keep powering on and off 5 or 10 times before it will completely boot up and display ready.

If that still fails then check and see if you have any smudges or points on your encoder strip where the lines have worn off. Go into the service menu: at "menu = full" (versus "short"; you'll get there somehow, don't have it in front of me), press "up arrow" and "enter" simultaneously to enter "service If the swithc itself appears to be defect, just short out the two wires, causin the machine to permanently think that the cover is closed.good luck. - Anonymous 0 Hi all Some pound them into a fold of wetted paper towel, but I wouldn't do that.