Home > Hp Designjet > Hp Designjet 5500 Error

Hp Designjet 5500 Error

Recommended action Turn the printer off (using the power switch at the back of the printer), wait 15 seconds and turn the printer on. Ensure the printer recognizes the memory installed. Click here for information on contacting HP Customer Care. Very helpful Somewhat helpful Not helpful End of contentUnited StatesHP WorldwideStart of Country / Region Selector contentSelect Your Country/Region and LanguageClick or use the tab key to select your countryArgentinaAustraliaBelgiqueBoliviaBrasilCanadaCanada-françaisČeská republikaChileColombiaDeutschlandEcuadorEspañaFranceIndiaIrelandItaliaMagyarországMéxicoNew Source

The front panel will display Firmware Upgrade. top System Error 0B0004 (non-continuable) Explanation Air Pressurization System (APS) failure. Attempt to verify printer functionality. If the error persists, upgrade the printer firmware (if upgrade is available).

Open the cover on the back of the printer to access the ink cartridge assembly (right side of the printer, looking from the back). Open the cover on the back of the printer to access the ink cartridge assembly (right side of the printer, looking from the back). Reseat or add memory (if needed). Loosen the two thumbscrews that attach the HP Jetdirect EIO card.

top System Error 0C1000 (non-continuable) Explanation The primer is not calibrated or the calibration settings have been lost. Remove media and re-boot the printer. 6 Designjet 5000 / 5500 ffff ffff 03450097 error If the Window is opened during the cutting operation, the Printer hangs and the Carriage suddenly If any of the printers are out of date, the application will prompt an update. Turn the printer off using the main power switch at the back of the printer.

Figure 5: 5000 series Mark encoder Remove the lens cover from the printhead carriage by pulling it straight out of the slot on the right side of the printhead carriage. Thank you! Follow the printer's front-panel instructions to replace the Lens cover (extra Lens covers are included in the Maintenance kit shipped with the printer). Anmelden Transkript Statistik 24.362 Aufrufe 14 Dieses Video gefällt dir?

Click here for information on how to replace the Lens cover . top System Error ffff ffff 03450097 Explanation The Top cover was opened during the cutting operation, the printer hangs and the Carriage suddenly stops. Depress, and hold the DOWN ARROW and the TOP key simultaneously, while turning the printer on using the main power switch (may require two people). Upgrade process If the System Maintenance Utility is unable to successfully upgrade firmware to a printer, send the files via DOS by connecting the printer to a PC through the parallel

Turn the main power switch on. WiedergabelisteWarteschlangeWiedergabelisteWarteschlange Alle entfernenBeenden Wird geladen... If the error re-occurs or the problem persists, turn the printer off and continue with the remaining steps. On the printer's front panel, scroll to the Cartridges menu.

top System Error 0B0005 (non-continuable) Explanation Air Pressurization System (APS) failure. this contact form If error appears frequently upgrade to firmware release A.02.xx 57 Designjet 5000 / 5500 0D0004 xxxxxxxx error (Non-Continuable) This is an internal general error code which can appear during the Printhead If the error re-appears, call HP for technical support to troubleshoot the problem. If the error persists, call HP for technical support to troubleshoot the problem.

Downloading the System Maintenance Utility Click here to go to www.Designjet.hp.com. Recommended action Turn the printer off (using the main power switch on the back of the printer) and remove the network cable from the printer's network card. Ensure the clear plastic tube is connected and not kinked in any way. http://permamatrix.net/hp-designjet/hp-designjet-5500-error-codes.html Recommended action Turn the printer off (using the power switch at the back of the printer), wait 15 seconds and turn the printer on.

Upgrade the firmware to the most current version available (instructions below). If the error continues after replacing the lens cover, call HP for technical support to troubleshoot the problem. Recommended action Turn the printer off (using the power switch at the back of the printer), wait 15 seconds and turn the printer on.

top System Error 010090 (continuable) Explanation An error has occurred in the Paper-axis Motor Encoder.

Recommended action Turn the printer off (using the power switch at the back of the printer), wait 15 seconds and turn the printer on. A message confirming the selection will appear, press ENTER to confirm (if the wrong part is selected, press BACK to cancel). Schließen Weitere Informationen View this message in English Du siehst YouTube auf Deutsch. If the error returns only when the printer is plugged into the network, the issue is most likely a network issue.Check the network settings (IP address, etc.) on the printer, workstation,

Even if the error appears again, there is nothing wrong with the Printer. 20 Designjet 5000 / 5500 050000 error (Continuable) Lens has problems reading the Mark Encoder on the Drive Press the Up Arrow key to move the drive roller until the Mark encoder is visible. Remove and re-install all six ink cartridges and press ENTER to continue. Check This Out If the error continues, call HP for technical support to troubleshoot the problem.

The error should disappear; however, if the error does return, turn the printer off and plug the power cord into a different power socket. Recommended action Turn the printer off (using the power switch at the back of the printer), wait 15 seconds and turn the printer on. Leaving media in the printer can result in error messages during the upgrade, or can cause the upgrade to fail. The User's Guide that came with your HP product.

Click here for instructions on how to upgrade the printer's firmware . This cause is not likely to be the Printhead because if it was, the Printhead would be marked as XX21 REPLACE. 51 Designjet 5000 / 5500 0C1000 error Primer not calibrated When the READY message is displayed on the front-panel, scroll to the Printer Setup Options icon and press the Enter key. Click here for information on contacting HP Customer Care.

top System Error 0A0040 (non-continuable) Explanation Air Pressurization System (APS) failure. Click here for information on contacting HP Customer Care. Recommended action Turn the printer off (using the power switch at the back of the printer), wait 15 seconds and turn the printer on.