Home > Hp Designjet > Hp Designjet 500 System Error 86 01

Hp Designjet 500 System Error 86 01

Contents

Click here for instructions on upgrading the printer's firmware . Click here for instructions on upgrading the printer's firmware . Some times the cable will catch bad enough to shut the carriage axis down which is why it is stopping. top System error 22:10 Explanation : Ink Supply Station failure Recommended action The possible cause could be: Reading, writing or initializing the backup EEROM failed. Source

NOTE: This error code only appears in HP Designjet 800 series, or in the Designjet 500 series printers with HP-GL/2 cards installed. Inspect the Y-belt for damage or excessive wear, and replace if necessary (refer to pg 8-40 of the Service Manual). Reinstall the accessory card cover. Recommended action Turn the printer off and allow a few minutes for printer to cool.

Hp Designjet 500 System Error 86 01

by dmzcompute on Jan 12, 2012 at 5:27pm Add comment Please sign in to comment 0 Thank you Dmzcompute for the response, but i got it lastnight... Keep holding the buttons tilll you hear a beep. Recommended action Upgrade the printer's firmware (if upgrade is available). Solution 1: If this error code appeared but was not caused by a paper jam, then try the following: Enter the Printer Information and check the Scan-Axis usage.

A.02.08, which fixes the issue. Click here to download HP drivers and/or software . by malvin on Apr 24, 2006 at 2:14pm Add comment Please sign in to comment 0 When the belt is starting to go you usually get shutdowns every once in the Hp Designjet 500 Error Codes If functionality is verified, no additional parts should be replaced.

Solution 3: Verify the Service Station Take out the service station and make sure it run through its full range of motion by rotating the motor spindle. Verify functionality Turn the printer on. The maximum length has been extended to 255 characters for an IP address and to 47 for an IPX address. https://h20565.www2.hp.com/hpsc/doc/public/display?sp4ts.oid=3558640&docId=emr_na-c04581797&docLocale=en_US Remove the Formatter card and re-install the Formatter card.

If the file is binary, use AppleTalk to send the file to the printer. 86.01 Possible Paper Jam I did put a little oil on the cutter end just in case, but this did not clear up the error. First you have to make sure the complete path of the carriage is smooth all the way from the right to the left. switch power on5.

Hp Designjet 800 System Error 86 01

Remove the HP-GL/2 accessory card and re-install the HP-GL/2 accessory card. http://h30434.www3.hp.com/t5/Inkjet-Printing/HP-DesignJet-800ps-error-86-01-severe-error-0x8010001/td-p/659247 Turn the printer on. Hp Designjet 500 System Error 86 01 CAUTION: Do not overtighten the screws. Hp Designjet 500 System Error 81:01 top System error 64:04 Explanation Firmware error (USB port).

Remove any such obstructions if possible. this contact form Turn the printer on. If the 21:10 error comes up, you may have a bad service station. so now that i have the carriage working LOL the black ink even tho its in there is saying missing ink... Hp Designjet 500 Paper Jam Error

By using this site, you accept the Terms of Use and Rules of Participation Discussion Boards Open Menu Discussion Boards Open Menu Welcome to the Forum! If the error re-appears, re-create the file and try printing again. Recommended action Click here for more information on resolving 79:04 errors . have a peek here Turn the printer on and attempt to verify functionality.

top System error 87:13 Explanation Unable to read the carriage encoder sensor. Hp Designjet 510 Error Codes Recommended action NOTE: Before continuing, verify that the parallel cable being used is an IEEE 1284 compliant cable no longer than 10 feet in length. NOTE: This error code only appears in HP Designjet 800 series, or in the Designjet 500 series printers with HP-GL/2 cards installed.

Turn on the printer, following initialization re-send the file that generated the error.

If the problem persists, click on Support at the top of the page for additional HP support and contact options. LOL lucky me i hope... Reply 1 1 8669 Student Posts: 1 Member Since: ‎07-03-2015 Message 3 of 4 (372 Views) Report Inappropriate Content Re: hp designjet 800 error code 86:01 Options Mark as New Bookmark Hp Designjet 500 Error 79:04 Very helpful Somewhat helpful Not helpful End of contentUnited StatesHP WorldwideStart of Country / Region Selector contentSelect Your Country/Region and LanguageClick or use the tab key to select your countryArgentinaAustraliaBelgiqueBoliviaBrasilCanadaCanada-françaisČeská republikaChileColombiaDeutschlandEcuadorEspañaFranceIndiaIrelandItaliaMagyarországMéxicoNew

align printheadHP DESIGNJET50042" also , jetdirect 620n not detecting. If the carriage is stuck at the right hand side of the Printer and cannot be moved out to the center of the Print Platen, likely it is because the Service For me, I believe it is due to two little 3/4 circle clips that fit into the carriage assembly and onto the sliding rod. Check This Out NOTE: A manila folder can be used to aid in removing jammed paper.

top System error 01:13 Explanation A problem with the Electronics module has occurred. by dmzcompute on Feb 17, 2014 at 5:25am Add comment Please sign in to comment I have tried that and other things like disconnect the power cord and nothing seems to Follow the instructions on the front panel. Thank you! Register · Log In HP Support Forum Home > Printers > DesignJet, Large Format Printers and Digital Press > [Solved] HP DesignJet 500 Error 86:01 when trying

However, please be aware that HP Service Manuals, technical updates and service notes are published available only for HP-Qualified Service Technicians. by mlemire on Mar 20, 2013 at 7:42am Add comment Please sign in to comment 0 There should be a screw on each side of the carriage assembly that tightens those top System error 01:12 Explanation The EEROM is not configured correctly. top System error 04:11 Explanation Jetdirect network card not detected.

by malvin on Apr 24, 2006 at 1:26pm Add comment Please sign in to comment 0 I do not usually work on 500 series, but with most plotters when there is If the error message persistss, check for a new release of the driver. If necessary, install more memory into the formatter. Recommended action Turn the printer off and allow a few minutes for printer to cool.