Home > Hp Designjet > Hp Designjet 500 Error Codes

Hp Designjet 500 Error Codes

Contents

If the problem persists, click on Support at the top of the page for additional HP support and contact options. top Removing/Installing (formatter card, HP-GL/2 card, Jetdirect print server) Turn the printer off and unplug the power cord. If the carriage is stuck at the right hand side of the Printer and cannot be moved out to the center of the Print Platen, likely it is because the Service If problems persists, continue with the remaining steps. Source

Wiping or rubbing this area may cause damage to the printhead. Plug the printer's power cord back in. The User's Guide that came with your HP product. 3. Recommended action Turn the printer off and allow a few minutes for printer to cool. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-c00993566

Hp Designjet 500 Error Codes

Before calling, please do the following: Review the following troubleshooting suggestions: Read the relevant driver documentation supplied with this printer (for users sending PostScript(R) files or those using Windows). They exist to help the engineer diagnose key areas for assessment, and can often indicate one or more parts have failed. Designjet Plotter Error Codes HP Designjet Error Codes The HP Designjet error code displayed on your large format (wide format) printer e.g. 11:11 86:01 79:04 does not always provide an exact

Click here for instructions on upgrading the printer's firmware . Your cache administrator is webmaster. top System error 05:10 (only applicable for Designjet 800 series) Explanation Formatter card failure, or Formatter card not detected. Hp Designjet 111 Error Codes If the problem persists, click on Support at the top of the page for additional HP support and contact options.

These products are now supported by Hewlett Packard Enterprise. Hp Designjet 500 Error Code 21 10 The two columns in the second indicator area show eight lights and one blinking light, indicating a total of nine in this area. If the printhead alignment was printed incorrectly with some print defects, replace the faulty printhead in which the color defects were noticeable. Click here for information on contacting HP Customer Care.

Turn the printer on and attempt to verify functionality. Hp Designjet 500 System Error 81 01 Remove the HP-GL/2 accessory card and re-install the HP-GL/2 accessory card. The maximum length has been extended to 255 characters for an IP address and to 47 for an IPX address. Recommended action Please call HP for technical support to troubleshoot the problem.

Hp Designjet 500 Error Code 21 10

Turn the printer on and attempt to verify functionality. If the problem persists, click on Support at the top of the page for additional HP support and contact options. Hp Designjet 500 Error Codes Turn the printer on and attempt to verify functionality. Hp Designjet 800 Formatter Card Turn the printer on and attempt to verify functionality.

Figure 4: Release buttons Remove the Cleanout assembly from the Printer. this contact form Solution: replace the formatter Recommended action Turn the printer off and unplug the power cable from the back of the printer. Recommended action Please call HP for technical support to troubleshoot the problem. That can damage the Carriage or the Service Station or both. Hp Designjet 800 System Error 05 10

If the file is binary, use AppleTalk to send the file to the printer. Plug in the power cable again and check to see if the error code has disappeared. top System error 21:10 Explanation Service Station failure Recommended action The possible cause could be: The steps counted by the Service Station motor are not consistent with the expected length of http://permamatrix.net/hp-designjet/hp-designjet-330-error-codes.html top System error 11:13 Explanation Problem with setting the voltage of the printheads.

Recommended action Turn the printer off and allow a few minutes for printer to cool. Hp Designjet 510 Error Codes top 81:01 error code Explanation There has been a paper-axis shutdown, which is usually a paper jam caused by a blockage of the paper-axis system. The first two digits explain which component/system is failing.

Your cache administrator is webmaster.

If AppleTalk is not being used to send the binary file to the printer, change the printer's internal PostScript settings to Binary (Set-up menu, PS settings, Encoding, Binary). If the problem persists, click on Support at the top of the page for additional HP support and contact options. Reinsert the printheads. Hp Designjet 500 Error 79:04 top System error 05:10 (only applicable for Designjet 500 series) Explanation HP-GL/2 accessory card failure.

top top System Warning codes Warnings will not be displayed on the front panel. top System error 93:10 Explanation Ink System startup failed. Plug in the power cable again and check to see if the error code has disappeared. Check This Out Recommended action Turn the printer off and allow five minutes for printer to cool.

Click here for information on contacting HP Customer Care. Open the folder where you saved the file (usually Downloads), double-click the file, and then follow the on-screen instructions to complete the installation. Open the main top cover, and check for any possible obstruction that may be preventing the carriage to move freely. If the rear path through is installed, remove it by pressing the buttons on each side and pulling it out.

top Contact HP? top System error 87:13 Explanation Unable to read the carriage encoder sensor. Recommended action Turn the printer off and unplug the power cable from the back of the printer. Generated Mon, 17 Oct 2016 20:35:37 GMT by s_wx1094 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.10/ Connection

Click here for information on how to clean the electrical contacts on the printheads.