Home > Hp Designjet > Hp Designjet 500 Error Code 21 10

Hp Designjet 500 Error Code 21 10

Contents

To check for the latest firmware updates for your printer using the HP website, go to HP Support Center . Turn the printer on and attempt to verify functionality. If the problem persists, click on Support at the top of the page for additional HP support and contact options. Other devices such as switchboxes can interfere with the communication between the computer and the HP Designjet 500, 510, or 800 series printer. http://permamatrix.net/hp-designjet/hp-designjet-800-error-code-21-10.html

Allow printer to complete initialization. Thank you! Click here to purchase parts and accessories from the HP Parts Store online at http://h20141.www2.hp.com/hpparts/. If the problem persists, click on Support at the top of the page for additional HP support and contact options.

Hp Designjet 500 Error Code 21 10

Generated Sun, 16 Oct 2016 09:41:57 GMT by s_ac4 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.9/ Connection In the Firmware section, click Download. Transkript Das interaktive Transkript konnte nicht geladen werden. Turn on the printer.

Recommended action Turn the printer off and unplug the power cable from the back of the printer. Troubleshooting: 1. top System error 71:04 Explanation Problem allocating memory. Hp Designjet 800 Formatter Card Lift the blue lever and insert the folder into the paper path to remove jammed paper.

NOTE: A manila folder can be used to aid in removing jammed paper. Hp Designjet 500 Error Codes Recommended action Turn the printer off and allow five minutes for printer to cool. Then unscrew the 2 screws attaching the HPGL2 card to the Electronics Module. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=mmr_kc-0102406 Set all other printer drivers that are set to print to the same port as the Designjet 800 or 500 Series printers to file.

If the problem persists, click on Support at the top of the page for additional HP support and contact options. Warning 61 05 Hp Designjet 500 IMPORTANT: For the DJ 500, it is recommended to remove the HPGL2 card (if installed) before updating the FW. Remove the HP Jetdirect card if installed. Remove the formatter card and re-install the formatter card.

Hp Designjet 500 Error Codes

top System error 56:13 Explanation An error in the drive roller encoder sensor quadrature has occurred. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-c03146392 From the front panel message of Ready, highlight the Printer icon, and press ENTER. Hp Designjet 500 Error Code 21 10 Recommended action Turn the printer off and allow a few minutes for printer to cool. Hp Designjet 500 System Error 21 10 Click here for instructions on upgrading the printer's firmware .

top System error 11:13 Explanation Problem with setting the voltage of the printheads. this contact form In any case, one who renders repairs to HP Designjet printers (self-help) is strongly recommended to refer to the applicable HP Service Manual, updates and service notes. After replacing all printhead, attempt to verify printer functionality. If the status of the Cyan Printhead is OK the conclusion is that the Cyan Printhead is working correctly. Hp Designjet 500 Error 79 04

Continue past system error 05:10, and attempt to print via the HP Designjet 500 print driver. Recommended action If the problem persists, click on Support at the top of the page for additional HP support and contact options. top top 79:04 errors when using version A.02.02 firmware or newer 79:04 error means "unexpected," "unknown," or "not assigned." Some of these errors are now better understood and have been remapped have a peek here That can damage the Carriage or the Service Station or both.

If the error re-appears, re-create the file and try printing again. Hp Designjet 800 System Error 05 10 Using the flat ended screwdriver, gently tighten the screws until the card is secure. If it prints successfully, go to software troubleshooting .

If it is unsuccessful, proceed to step 3.

Use the blue handle on every PH to lift them up. Please try again later. Recommended action Turn the printer off and allow a few minutes for printer to cool. Hp Designjet 500 Firmware Update Download Try sending a different file.

top System error 61:04 Explanation Firmware error. If the problem persists, click on Support at the top of the page for additional HP support and contact options. Remove all PRINTHEADS (PHs) from the carriage. Check This Out Ensure the parallel cable is properly connected to the PC and printer.

If the file is PostScript, check to see if it is binary. If the problem persists, click on Support at the top of the page for additional HP support and contact options. Wird verarbeitet... Plug the power cable in and turn the printer on.

Recommended action Follow the instructions below to help solve the issue: Turn the printer off and allow a few minutes for printer to cool. ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.8/ Connection to 0.0.0.8 failed. Troubleshooting printer functionality The 61:05 error can occur from dirty printhead contacts or a bad printhead (may rotate between a 79:04 error depending on job being sent or internal print being Plug the power cable in, turn the printer on and attempt to verify functionality.

Sign-in Register Site help Skip to ContentSkip to FooterLaptops & tablets Business Premium Gaming Standard laptops Workstations Convertibles & detachables Tablets 3-in-1 Desktops Business Immersive Gaming Towers Workstations All-in-ones 3-in-1 Printers top System error 43:11 Explanation The Vacuum fan is not detected. Hinzuf├╝gen Playlists werden geladen... If the problem persists, click on Support at the top of the page for additional HP support and contact options.

Other devices such as switchboxes can interfere with the communication between the computer and the printer. This product has been successfully added to your profile. Expired PHs can be the cause of the System Error. top System error 02:13 Explanation A problem has occurred with the carriage assembly.

Plug the power cable in, turn the printer on and attempt to verify functionality. top System error 86:01 Explanation Carriage-Axis shutdown.