Home > Hp Designjet > Hp Designjet 350c Error

Hp Designjet 350c Error

If a failure occurs, an error is indicated on the front-panel LEDs. Keep in mind that the value printed on the service configuration plot may greatly underestimate the amount of ink in the spittoon. After realigning, the right edge of the media is checked again for skew (misalignment). (The loading process fails if the skew is greater than the allowed limits or if the aligned General Cleaning Proper general cleaning should include the following: 1 Blow away dust accumulation with compressed air if available. 2 Clean the outer surface of the plotter with a damp sponge Source

Readership The procedures described in this manual are to be performed by HP-certified service personnel only. NOTE: If the printer recognizes the cover as closed, it will not see a removal or insertion of a cartridge. The pinch-arm sensor is electrically connected to the main PCA. C4699-90000 Removal and Replacement 6-11 Reinstalling the front-panel assembly: Insert the bottom of the assembly into the two indicated notches, inside the right end-cover.

Apply oil (Anderol 4068, HP part number: 6040-0858) to the slider rod (± 3 drops) and to the bushings if they are running dry. The plotter builds graphic display objects on a swath-by-swath basis. Unload the sheet from the printer. Set the Media Type on the front panel to Film.

It is one exchangeable part. Also note that the factory spittoon value on the cleared or new EEROM is 0%. Be careful not to damage the parallel-port clamps. 11 If you are changing the electronics module for a new one, remove the DRAM SIMM(if installed) from the old module and install Ask Brad829 Your Own Question Brad829, Technician Category: Consumer Electronics Satisfied Customers: 335 Experience: 40+ years in the industry as well as a Ham radio extra class operator. 14541849 Type Your

Unload the sheet from the printer. Serial Interface 3. Page Size /sest O /best O Best O El O Inked Area O Software O /Best O 1^0 1 AO / B1 O 1 D O 1 A1 1 ^ ANsI Electrical Shock Hazard Serious shock hazard leading to death or injury may result if you do not take the following precautions: • Ensure that the ac power outlet (mains) has a

NOTE: It is also necessary to adjust the Carriage to Media distance using the instructions and gauge that come with the new Carriage assembly. by boycee on Mar 25, 2005 at 11:33am Add comment Please sign in to comment 0 I have the same problem to did anyone figure out how to fix it? Part Numbers Part numbers for plotter options, accessories and service parts are located in chapter 10. Mark parity is not supported.

Generated Mon, 17 Oct 2016 22:11:35 GMT by s_ac15 (squid/3.5.20) click here now Wird geladen... Über YouTube Presse Urheberrecht YouTuber Werbung Entwickler +YouTube Nutzungsbedingungen Datenschutz Richtlinien und Sicherheit Feedback senden Probier mal was Neues aus! Repacking the Plotter You can order a repacking kit if you need to repack the plotter and don't have the shipping container and insulation material. (Part numbers i^ chapter 10.) 3-4 Cycle power, service.

search Search the Wayback Machine Featured texts All Texts latest This Just In Smithsonian Libraries FEDLINK (US) Genealogy Lincoln Collection Additional Collections eBooks & Texts Top American Libraries Canadian Libraries Universal this contact form WARNING The procedures described in this manual are to be performed by HP-qualified service personnel only. Memory Usage It is difficult to calculate the amount of plotter memory needed to plot a drawing of any given file size. Reload the sheet with the print side down, so the printer can calibrate the new values selected.

Cleaning intervals are determined by the plotter environment and by the types of plotter supplies used. It calls attention to an operating procedure, practice, or the like, which, if not correctly performed or adhered to, could result in damage to or destruction of part or all of An autoswitching feature enables the plotter to detect from which interface it is receiving data, so you can send data through either interface without having to change the plotter settings. (More have a peek here To recover from moisture condensation, turn the plotter off, and, using the main roller as a reference, wait until the plotter is completely dry before using it again. (Other environmental specifications

If the Ready LED does not turn off, replace Front Panel Assy (refer to pages 6-12 of the 300 Series Service Manual). The software issues a command (referred to in RTL as no negative motion) telling the plotter that it will not receive data for any media location on which it has already This enables you to send data through different networks without having to change the interface settings.

If the issue persists, replace the Electronics module (refer to pages 6-13 of the 300 Series Service Manual).

If the same cartridge fails in another color slot, the cartridge must be replaced. Thank you! Perform an accuracy calibration (listed below) and verify functionality.Accuracy calibration Place a sheet of polyester film over the top of the printer for approximately 10 minutes to let it stabilize to Allow several minutes for the printer to complete the calibration print.

Oil stays inside them by means of capillary action. When the Ready LED lights up, press the ACCURACY CALIBRATION key. NOTE: If a polyester or matte film is not available, use HP Coated media when performing an accuracy calibration. http://permamatrix.net/hp-designjet/hp-designjet-500-firmware.html Accuracy The accuracy of the plotters in drawing a vector is ± 0.38 mm (0.015 in) or ± 0.2% of the specified vector length, whichever is greater, at 23 °C (73

A charge can cause the media to stick to itself and jam the plotter. At power-on the plotter firmware identifies whether the carriage is for a color or a monochrome model, and behaves accordingly. Avda. This will help in determining defective cartridges or Carriage slots.

A wick attached to the underside of the right side-plate routes water drops away from the main-PCA electronics. Data flows through the plotter without being stored in a display list, so the size of the file that you can send is almost unlimited.