Home > Hp Designjet > Hp Designjet 2500cp System Error

Hp Designjet 2500cp System Error

Check that the air tubes that are connected between the primer assembly and the service station are in the correct position and are not squeezed together. REMEMBER THAT CERTAIN CALIBRATIONS ARE REQUIRED EVEN IF AN ASSEMBLY HAS BEEN DISASSEMBLED TO GAIN ACCESS TO ANOTHER ASSEMBLY OR COMPONENT. Recommended Action Turn the printer off, then on. If they break, you have to try to fix them, or buy a whole new service station assembly.They dont sell just the sled part. have a peek here

Recommended Action Turn the printer off using the power switch on the back of the printer. search Search the Wayback Machine Featured texts All Texts latest This Just In Smithsonian Libraries FEDLINK (US) Genealogy Lincoln Collection Additional Collections eBooks & Texts Top American Libraries Canadian Libraries Universal Check if the Media used is suitable for the printer. Using this procedure you will be able to determine exactly which component failed. 2-8 HP DesignJet CP Series Printers System Error Codes System E r ror : 010033 Problem Description: The

If the test fails, replace the Service Station assembly (refer to pages 8-26, 8-87 of the service manual). noises) at mid-page refills. 5 "Big print" feature. Replace Cutter Assembly. D15.

Check that the flag is installed correctly. D14. Have you performed a Service Test on the Failed Component/Assembly? THE DATA ON THE FLASH SIMM IS BEING ERASED AT THIS POINT.

Recommended Action Turn the printer off, then on. No part of this document may be photocopied, reproduced, or translated into another language without the prior written consent of Hewlett- Packard Company. Substitute "devi ce.fi le" with the name of your Workstation parallel device file. . http://www.computercarefiles.com/TWI_Docs/bpp90053/default.html Perform the Electronics test.

If the error reappears, contact HP support . This short circuit is causing some of the fuses in the Electronics Moduleto burn. A.02.XX -This firmware revision is applicable to HP DesignJ ets2500CP and 2000CP and means that the Printers can use both the Imaging Inks and the new U V Durable I nks. Product functionality cannot be guaranteed with 3rd party RAM SIMMs. • If more than one RAM SIMM (memory module) is installed, remove one of them and power on the printer again.

top System error 060300 Explanation Incompatibility between Firmware FW A.01.07 and the new Line Sensor Recommended Action Upgrade Firmware. http://fixyourownprinter.com/posts/22887 The Printer MUST be kept away from direct intense sunlight or a spotlight. HP DesignJet 2500CP only System Error: 08xxxx — PostScript Error. top System error 010120 Explanation The configuration area of the EEROM is not valid.

Check/replace Refill Interconnect Cable. navigate here Locate the Mark encoder on the end of the Drive roller. If the error reappears, contact HP support . NOTE: If the printer has been serviced recently, make sure the Service Station nut is installed correctly (new Service Stations C4723-60276 have the nut).

If this system error appears again then try to replace both RAM SIMMs with new ones. • If the Error Data is lower than A4000000 then the failure is in the If the media is not HP approved, advise the customer to use HP media and check to see if the problem is now solved. NOTE: If the mark encoder is not visible, turn the printer off, then on. http://permamatrix.net/hp-designjet/hp-designjet-500-system-error-86-01.html Corrective Action: Try the foil owing: • Switch the Printer OFF from the back and then disconnect theTrailing Cablefromthe Electronics Module.

If the error reappears, contact HP support . REPLACE THE LENS COVER BEFORE YOU PERFORM THIS CALIBRATION IN ORDER TO PREVENT ANY AEROSOL PROBLEMS. The solution.

C08.

If "D1700 OK" - Counters reset correctly. Check Line Sensor is installed/connected correctly. A small arrow t is used to indicate other parts of the Service Manual or User's Guide where you can find information related to the topic you are consulting. Corrective Action: Try the following: � Make sure that the Service Station Interconnect Cable (the black cable that connects the Service Station to the Electronics Module) is correctly connected to the

Replace lens cover which is installed on the line sensor. M ai ntenance 5-18 C10. Replace Refill Assembly. this contact form Troubleshooting HP DesignJet CP Series Printers 1 -9 What can I do if the Cover Sensors arent Working? 1 Check if the faulty sensor is installed correctly. 2 Check if the

Perform the Line Sensor calibration. top System error 080001 Explanation Hard disk installed without PostScript. top System error 08xxxx Explanation PostScript error.