Home > Hp Designjet > Hp Designjet 1055cm Error Codes

Hp Designjet 1055cm Error Codes

Contents

Now move the carriage all the way to the left. I can cycle the power and unit will work again for awhile but will fail again and again. CtilP JET D-T'' llfckE. I have checked and reseated all connections..I then replaced the main logic board. Source

by dmzcompute on Sep 30, 2013 at 3:33pm Add comment Please sign in to comment 0 I removed the encoder strip off of the back of the printer, and cleaned it I14TLS 5U/LLL- piJilk* ..-J- ►.- ■ ■ •■ : ft-; 1H.L:i HP DesignJets 1050C and 1055CM Printers Service Manual 1-21 Troubleshooting 1-22 HP DesignJets 1050C and 1055CM Printers Service Manual System Return to TWI Documents Library Index Page HP Designjet 1000 Series Printers - TWI: System Error 0B0007 In this document: Tools required Parts required (part numbers are subject to change) Troubleshooting This causes two main problems: 1. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-bpp03899

Hp Designjet 1055cm Error Codes

Unclog any holes with a straightened paperclip or other appropriate tool. When reporting the error, have the following information ready: ■ Model and Serial Number of the printer. ■ Which firmware revision the printer is using (See Note below). Contact HP? Check all the cables of the APS and make sure they are correctly connected and are NOT damaged.

Ink Pressure System 4-14 5. If there is Ink Leakage, replace ALL Ink Cartridges, the APS ( = Page 8-20) and the Tubes System ( => Page 8-53). HP DesignJets 1050C and 1055CM Printers Service Manual 1-9 Troubleshooting Printhead Crashes/Smears on High Density Prints Using Coated Media High density prints can cause cockle mainly on HP Coated Media. Hp Designjet 1050c Error 060308 00000008 I did clean all the crud out of the gear so i would assume it was ok but the error keeps coming back up, and it has displayed a 1 as

Release the cable that is attached to the top of the right side cover (see Figure 9). Hp Designjet 1050c Service Manual Switch the Printer ON again. You could try HP tech support although its very hard to get a hold of an actual real tech anymore. Any ideas would be a great help.Thanks Respond to this 1 Has anyone had this problemm..

Remove the left door. Hp Designjet 1050c Printhead is it supposed to be attached to the slider rod or on the frame itself?Cheers - Freak 0 Yes it supposed to be attached to the slider rod or on the by dmzcompute on Apr 14, 2008 at 4:29pm Add comment Please sign in to comment 0 i just changed the belt on this machine, i replaced the trailling cable, checked the If the sensor/switch is broken, then the cover needs to be replaced.

Hp Designjet 1050c Service Manual

This site is also for customers who need to change their maintenance kits irrespective of their warranty status. visit I opened the right cover and tried to clean the motor pulley but there was so much gunk on it that I had to open the motor. Hp Designjet 1055cm Error Codes It went a little bit further this time, but the message still appeared. Hp Designjet 1055cm Plus System Error Codes When reporting the error, have the following information ready: ■ Model and Serial Number of the printer. ■ Which firmware revision the printer is using (See Note below).

The procedures described in this manual are to be performed by HP-qualified service personnel only. http://permamatrix.net/hp-designjet/hp-designjet-330-error-codes.html a 1 fa 2 <* 11 s b s s 1 1 1 > s 2 1 ■a ejj J in o en < 53 o ol O The ink supply tube assy has just been replaced and even lubricated to insure proper movement but unit has failed just a week later. System error 02:10 A problem has occurred with the carriage assembly System error 02:13 A problem has occurred with the carriage assembly. System Error 060308 00000008

Usually the plotter does a self test and after that starts the initialization and the motor will start to turn at that point moving the carriage all the way to the by Anonymous on May 18, 2009 at 10:05pm Add comment Please sign in to comment 0 I believe there were three types of boards made and it had more to do To in the back of the carriage which must be loosened to alllow the screw at the top center back of the carriage to be adjusted clockwise to raise the carrriage have a peek here To solve the problem, try the following: ■ Check in the Front Panel if Ink Limiting is ON or OFF.

System error 72:04 Problem in the scan-axis (firmware error). Hp Designjet 1050c Driver Clean the Overdrive using the Overdrive Cleaning Service Utility => Page 4-37. How does that tell you anything?

Hewlett Packard Certified Factory Trained in HP Design Jet 500 plotter repair in USA Nationwide we use only original HP plotter service/repair parts.

by copyplus on Sep 4, 2014 at 5:26pm Add comment Please sign in to comment 0 Just got this from an auction. Adjust the carriage to the correct height => Page 5-24 and try to load the media again. by iscott on Nov 15, 2010 at 4:05pm Add comment Please sign in to comment 0 For the tube assembly there are a couple of things you can try. Lps Computer HP No.80 Ink Supplies Troubleshootingpage 57................................................................................................................................................................

Now if the non plus model you may be up a creek without a paddle. Corrective Action: Refer to System Error Code 070100. Close Yeah, keep it Undo Close This video is unavailable. Check This Out by qman29 on Oct 3, 2011 at 3:26pm Add comment Please sign in to comment 0 I have the same problem I replaced the belt and get the print head error.

I learned by my mistake and always take a reading before I disconnect the cables just to be sure. The instructor soldered a fuse over the blown one on the board, did not remove the old one. by dmzcompute on May 1, 2007 at 8:09pm Add comment Please sign in to comment 0 I use an HP 1050C and I am having a similar problem. Turn the printer on, and repeat steps 1-8.

ICJ",' I" liri-uh , :i.mf.y,- UPLETfLn. Sometimes just putting a light coat of grease on the part of the tube that rubs will solve the issue and other times it has to be replaced. System Error: Problem Description: Corrective Action: Try the following: 06030A (Continuable) Error in finding the Mark Encoder. The Line Sensor has Problems Detecting Media 1 Check the type of media that is being used since the Line sensor may have problems detecting transparent media or some types of

I also noted that the belt was bouncing around at the same time. If you get a bumping action, the problem is probably the belt is starting to wear and particles from the belt are adhering to the motor shaft and the belt will HOinfl nL>b u><2DhCIMlLC ^wLHEfS: TAftii IIPEIIIIJ^I ■(■! 'SL'X FfWroUI. If the error appears following replacement of all suspected printheads, contact HP.

Description: Corrective Action: Try the following: Perform the Service Station Calibration => Page 5-11.