Home > Hp Designjet > Hp Designjet 1050c Service Manual

Hp Designjet 1050c Service Manual

Contents

Page 63: The Front Panel Display The Front Panel Display The front panel display has a dedicated area to report the status of your HP No.80 supplies. Page 173: Parts And Diagrams Scan-Axis Assemblies 7-20 Drive Roller and ARSS Miscellaneous Parts 7-22 Paper Path Assemblies 7-24 Pinch Assembly 7-26 Drive Roller Assemblies 7-28 Center Guide and Media Sensor Safety Symbols General definitions of safety symbols are given immediately after the table of contents. Page 45 System Error Codes 06030B System Error: The Ambient Temperature measured is out of the normal range. have a peek at this web-site

Electronics Module 2. IIO Configuration - In this area you can find information on the configuration of the JetDirect Card 1-20 Back Enter HP DesignJets 1050C and 1055CM Printers Service Manual Press Enter... Page 72 Carriage Assembly is faulty. HP DesignJets 1050C and 1055CM Printers Service Manual System Error Codes Page 5-11.

Hp Designjet 1050c Service Manual

Using this procedure you will be able to determine exactly which component failed. Conventions A small arrow => is used to indicate other parts of the Service Manual where you can find information related to the topic you are consulting. T3 O £ p u s ■3 p © s 3 2:2 h iff u p 0- CL 1-18 HP DesignJets 1050C and 1055CM Printers Service Manual Troubleshooting Service Configuration Print Page 23: Hp-gl/2 Color Differences In Different Hp Designjet Printers "still-not-printed" media or damaging the actual print.

To verify if there really is a problem with the Vacuum Fan, try the following: With the Printer ON, open the Window of the Printer and place a sheet of HP IF THIS TEST PASSES, DO NOT REPLACE THE HARD DISK DRIVE. Do NOT use any other type of media apart from HP Coated or HP High Gloss Photo Paper. 1 In the Service Calibrations submenu, scroll to "3. Hp Designjet 1055cm Plus Troubleshooting IF THIS TEST PASSES, DO NOT REPLACE THE PAPER AXIS MOTOR.

The 1050c will print a small amount (about 12" or so). Hp Designjet 1055cm Plus Manual Page 128 Check that the Calibrations are done and within the limits 5-12 Back Enter Performing drop detector calibration. Please wait. Page 168 Banding in black column only.

Page 4-37). Hp Designjet 1050c Plus Parts EIO Card 4-10 3. Page 58: What Are Hp No.80 Supplies?, Ink Cartridges, Printheads And Printhead Cleaners Printhead Cleaner Ink Cartridge Ink Cartridges The HP No.80 ink cartridges for the HP DesignJet 1050C and 1055CM Perform the Accuracy Calibration as follows: Make sure you load HP High Gloss Photo Paper in to the Printer NOTE before performing this calibration.

Hp Designjet 1055cm Plus Manual

How to Print the Service Configuration Print 1 Load media (Roll media or at least an A4 Sheet) into the Printer. 2 Once the message "Ready" is displayed on the front-panel, weblink System Error: Problem Description: Corrective Action: Try the following: 06030A (Continuable) Error in finding the Mark Encoder. Hp Designjet 1050c Service Manual Page 165: Problems With Horizontal Lines (banding) Print Quality Problems with Horizontal Lines (Banding) Description of problem When you look at the image you have printed there are light or dark Hp Designjet 1050c Owners Manual Page 18: The Printer Continuously Rejects Printheads, Cover Sensors Are Not Working 1 Check the type of media that is being used since the Line sensor may have problems detecting transparent

Page 120: Entering The Service Calibrations Menu Service Calibrations Entering the Service Calibrations Menu 1 Once the message "Ready" is displayed on the front-panel, scroll to the "Printer Setup Options" icon Check This Out When removing the Service Station, make sure that you release... The Image Quality Print will help you differentiate between possible printhead errors and other problems such as incorrect front-panel selection, driver or RIP configuration or mechanical problems. PWM is less than 85, then the test has passed. Hp Designjet 1055cm Network Configuration

If the Error Code reappears, then the Printer requires an on-site visit in order to resolve the problem. Page 72 HP No.80 Ink Supplies Troubleshooting The printhead has moved slightly and is not making good electrical Reseat contact with the carriage assembly. Page 122: Accuracy Calibration Service Calibrations 1. Source Service station... 4.

Page 68: Ink Cartridge Status While Replacing The ink cartridge is having continuity problems. Hp Designjet 1055cm Plus Parts Replace the Electronics Module ⇒... Check that the Service Station Encoder-Cable is correctly connected.

P/s use our SmartSearch to locate your part number.

Problem Description: Try the following: Corrective Action: Make sure that the Aerosol Fan is connected correctly to the Electronics Module. Page 56 System Error Codes 0B000B System Error: Pump or Pressure Sensor not working. Preheat a good oven to 350F (177C) and when the oven is ready, place the pan with the card in the oven for 8 minutes. Hp Designjet 1055cm Parts the usage time, go to page Printhead life is anticipated to be 700ml or twelve months (9,000 hours) in the printer, whichever occurs first, provided that the...

Although this information is provided for your convenience it is recommended, for the most part, that a technician inspects your office equipment. EEROM Utilities 4-38 7. Remove the Right Hand Trim (Item 2) from the Printer. have a peek here Turn the Printer OFF and disconnect the Aerosol Fan from the Electronics Module.

This will release the complete assembly. 8-14 Figure 9: Tube Grip Figure 10: Latches HP DesignJets 1050C and 1055CM Printers Service Manual 2082a... Corrective Action: Try the following: ■ The leak detector could have been triggered due to condensation in the Printer. NOTE Make sure that there is enough ink remaining in the Ink Cartridges before starting to prime the tubes. Remove and let cool for 10 minutes.

After removing any PCA from the Printer, place it on a conductive foam pad or into its conductive packaging to prevent ESD damage to any ICs on the PCA. Page 17: The Printer Does Not Power On 2 Check that the Firmware DIMM is installed correctly in the correct slot (the first slot from the right) at the back of Problem Description: Try the following: Corrective Action: Check that the cable from the Ink Supply Station (ISS) PCA to the Ink Supply Station is correctly connected. Ready CYAN MAGENTA...

In this case, replace the Platen Assembly => Page 8-63. Japanese ... Problem Description: Refer to System Error Code 070100. HP DesignJets 1050C and 1055CM Printers Service Manual Print Quality C6074283 6-13...

Page 223 Figure 11: Ink Cartridge Tube Connector (pulled back) 5. Hard Disk Drive 4-12 4. Overdrive Cleaning The purpose of this Service Utility is to rotate the Overdrive, Drive Roller and Roller Mark in order to clean them. Page 93 Strip using a damp cloth.

System Error: Problem Description: Corrective Action: Try the following: 0C0030 Bad Drop Detector. If the Error Code continues, replace the Electronics Module ⇒... Page 117: Service Calibrations Service Calibrations Service Calibrations 5-2 Entering the Service Calibrations Menu 5-4 1.