Home > Hp Designjet > Hp Designjet 1050c Printhead Path Type 2

Hp Designjet 1050c Printhead Path Type 2

Contents

To make things easier for everyone concerned if you still have an issue only post what happens when you move the carriage assembly by hand and that is after you have plotter jam remove service station error check printhead cleaner manual 10 bar amp View Less » 2,902 people viewed this question Ask a Question Usually answered in minutes! Now if the non plus model you may be up a creek without a paddle. Your answer needs to include more details to help people. http://permamatrix.net/hp-designjet/check-printhead-path-type-1.html

The service station is pulled forward to enable you to move the carriage out of the way. Turn the printer off, using the main power switch located on the back of the printer. DesignJet 1050c plus... Check around the ends, front, and rear edges of the platen roller to verify that all of the torn media is removed.

Hp Designjet 1050c Printhead Path Type 2

Unload media and check for obstructions in the carriage path, remove as needed. The belt was installed new about 5 months ago. One thing I noticed is that now the digital screen is surging in brightness every once in a while....not sure if this is related.

HP DesignJet Printers &... The printhead shoots back and forth...the motor looks functional. That seemed to take care of it. Switch Power Off Check Printhead Path 1 Slide the carriage out of the way toward either side of the enclosed ends of the printer (if needed).

I am hiring a professional to service our 1055CM with a Type(2) error, but I'll be knowledgeably watching over his shoulder.Thanks by unknown on Oct 22, 2008 at 9:58am Add comment Check Printhead Path Type 1 Thank you! the only way to change the status is to change printheads. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-bpp03414 If the sensor/switch is broken, then the cover needs to be replaced.

How to do to not change them now, but to do like that - to... Hp Designjet 1050c Printhead Alignment Error I have ruled out the motor due to the above posts, but was also thinking about possibly replacing the carriage assembly. Posted on Oct 01, 2009 Helpful 0 Not Helpful Comment Flag You can't post conmments that contain an email address. × Comment Anonymously Video Images Add Your Answer Tips for a Once inside the Utilities menu, press the Up Arrow key and the ENTER key simultaneously.

Check Printhead Path Type 1

I replaced the tensioner pulley with a new one, I believe it was new. http://www.fixyourownprinter.com/posts/47311 MVP: An expert that got 5 achievements. Hp Designjet 1050c Printhead Path Type 2 I oiled the rails again ao i don't know. Hp Designjet 1055cm Check Printhead Path Type(1) While I had it apart I used a brush and a can of Dust Off to clean it out (including motor gear).

I spent a lot of time explaining what I have seen and done over the years and if you bother to read what I have posted you might be able to this contact form Ouch! Any ideas? This message comes when print head is not fitted or locked properly in the socket, please remove printhead, also check for polythene conver on nozzle that should be also removed. Hp Designjet 1055cm Check Printhead Cleaner Path

Use a manila folder to remove jammed media from the media path (take care not to damage the media sensor on the right side of the printer). Loading... View Most Popular DesignJet 1050c plus InkJet Printer Printers & Copiers Related Question I have hp designjet 450c..the problem in printing.while printing it prints copy of the image also and not http://permamatrix.net/hp-designjet/hp-designjet-1050c-service-manual.html It could be a variety of things i.e.

the plotter doesn't recognize the cleaners on the right hand side of the plotter, I have replaced them and started the plotter again and still comes up saying that I have Hp Designjet 1055cm Printhead Failed Usually the plotter does a self test and after that starts the initialization and the motor will start to turn at that point moving the carriage all the way to the Perform a Scan-axis test (Diagnostics menu).

If the tube assembly is the issue it has to be attached in order to run.

Any other ideas? I fully cleaned the motor pulley, installed back and applied some oil on both the shafts and put the cover back. Learn How to Post and More  Community News  Best of the Community Blog  Notebooks Notebook Operating System and Recovery  Notebook Boot and Lockup  Notebook Wireless and Networking  Notebook Audio  Notebook Video, Hp Designjet 1055cm Check Printhead Path 2 Open the top cover and examine the area under the belt and look for debris that looks like pencil erasure crumbs.

I also noted that the belt was bouncing around at the same time. Showing results for  Search instead for  Do you mean  or Post new question Question Reply Topic Options Subscribe Mark Topic as New Mark Topic as Read Float this Topic to the Did you remove and clean out belt residue from the grooves on the motor shaft and pulley when you replaced the belt? http://permamatrix.net/hp-designjet/hp-designjet-1050c-system-error-04c300.html DesignJet 1050c plus InkJet Printer...

Now move the carriage assembly out and then using the belt move the carriage assembly back and forth over the complete width and see if you can spot and tight spots When you have that tighten the 2 screws in the rear, run the carriage one more time the complete path to make sure there is no noise, remove the height tool, a worn carriage belt, service station not moving out of the way correctly but the most common cause is the basic one of dirty rails. To in the back of the carriage which must be loosened to alllow the screw at the top center back of the carriage to be adjusted clockwise to raise the carrriage

If the problem persists, generate a CSO for service (send ALL required parts as listed below).Parts required (part numbers are subject to change) Part description Models - C6090A/V, C6091A/V Models - If the belt is not positioned correctly on the carriage assembly when it moves in one direction it eventually can no longer be moved since the pully portion is now over There is a special tool used for this purpose.