Home > Hp Color > Hp Color Laserjet 4700 Only Printing Black And White

Hp Color Laserjet 4700 Only Printing Black And White

Contents

If you have an active support agreement or HP Care Pack, you can link them to your profile to ensure access to all services. The values of YY are: 00 = black print cartridge 01 = cyan print cartridge 02 = magenta print cartridge 03 = yellow print cartridge Action No action necessary. top 41.5 UNEXPECTED TYPE IN TRAY X For help press alternates with LOAD TRAY XX [TYPE] [SIZE] To use another tray press Description The printer senses a different media type in When the maximum number of sheets for a specific media type is reached, the job is ejected and handled as a stacked job. have a peek at this web-site

Reduce the complexity of the print job to avoid this error in the future. Supplies ordering information is also available from the embedded Web server. Rotating [COLOR]motorTo exit press. eCommerce Solution : k-eCommerce Home HP Color Laserjet 4700: 59.30 error by Seymour2035 on Jan 16, 2012 at 10:28 UTC | Printers, Copiers, Scanners & Faxes 0Spice Down Next: Setting up http://h20564.www2.hp.com/portal/site/hpsc/public/psi/troubleshootResults?sp4ts.oid=473038

Hp Color Laserjet 4700 Only Printing Black And White

Action Replace the color cartridge. 10.92.YY CARTRIDGES NOT ENGAGED Description The print cartridge is not seated properly in the printer. No action necessary. alternates with For help press (question mark) The supplies gauge will display the consumption levels of print cartridges.

If this error occurs, the printer will continue to track the time and date using the processor clock until the printer is turned Off. This section explains the differences between the control panel message types. The amber light on the stapler/ stacker is blinking. Hp 4700 Colors Not Aligned No action necessary.

The printer is ready and will continue for the estimated number of pages indicated. Hp Color Laserjet 4700 Not Printing Color We do have a Server 2008 r2 as well set up as a secondary print server for testing problems with printers especially odd issues we've had with the 4700's.  I have The cartridge is either not installed or not correctly installed in the printer. LOAD TRAY 1: <(less than)TYPE> (greater than) <(less than) SIZE> (greater than) To continue press (check mark) alternates with LOAD TRAY 1: <(less than) TYPE> (greater than) <(less than) SIZE> (greater

The amber light on the stacker/stapler is blinking. Hp Color Laserjet 4700 Color Calibration Receiving upgrade A firmware upgrade is in progress. Turn the printer on after reseating the 500-sheet input tray. CHOSEN PERSONALITY NOT AVAILABLE To continue press (check mark) alternates with CHOSEN PERSONALITY NOT AVAILABLE For help press (question mark) PJL encountered a request for a personality that did not exist

Hp Color Laserjet 4700 Not Printing Color

This includes the top cover area. Supplies ordering information is also available from the embedded Web server. Hp Color Laserjet 4700 Only Printing Black And White Press (question mark)to view help for the message. Hp 4700 Service Manual The stapler/stacker cannot operate in this condition.

They change as the state of the printer changes. Check This Out If the message persists, turn the printer off then on. A job cannot be stored because of a memory, disk, or configuration problem. If prompted, confirm the size and type of paper loaded. Hp Color Laserjet 4700 Printing Shadows

If you have any suspicions about the fuser  then I would replace the fuser. I no longer get the 49.4c02 error message however it will still not print. The identified print cartridge has reached the end of life and the COLOR SUPPLY OUT setting in the SYSTEM SETUP menu is set to STOP AT LOW. http://permamatrix.net/hp-color/hp-color-laserjet-fuser-error-50-1.html NON HP SUPPLY IN USE alternates with Ready The supplies gauge will display the consumption levels of print cartridges, but the level of any refilled cartridge will not be shown.

Stop BAD DUPLEXERCONNECTION REPLACE [COLOR]CARTRIDGE Calibrating.. Hp 4700 Fuser Reset DIAGNOSTICS PAGE The printer is generating the diagnostics page. If the message persists, turn the printer off then on. [FS] FILE OPERATION FAILED To clear press (check mark) alternates with Ready The printer received a PJL file system command that

More than one supply item is low.

I can ping the printer and I can ping computers on the network from the printer.  I did find on the server in the event viewer a "Win32 error code returned You just need to make sure you defeated the cover interlock switch.Ok now that we troubleshooted the HP color laserjet 4700, 4730 MFP, and CP4005 59.30 fuser error message it's time If the problem persists, contact HP Support at www.hp.com/support/clj4700 top 54.01 PRINTER ERROR To continue turn Off then On Description Printing cannot continue. Hp Color Laserjet 4700 Printer Troubleshoot If the error does not clear, record the message and contact HP Support at www.hp.com/support/clj4700 top top 66.XX.X OUTPUT DEVICE FAILURE Description The stapler/stacker has failed.

If the message persists, turn the printer off and then on. Printing... This section explains the differences between the control panel message types. have a peek here Close the jam access door.

View tray configurations (type and size) using (down arrow) and (up arrow). Printing can continue, but there may be unexpected behavior. Order a print cartridge NOTE: Supplies ordering information is also available from the embedded Web server. Press Menu to enter the MENUS.2.

If the message persists, turn the printer off then on. Printing... A cleaning page is being processed. Printing...

The values of YY are: 00 = black print cartridge 01 = cyan print cartridge 02 = magenta print cartridge 03 = yellow print cartridge Action Replace the print cartridge indicated.