Home > Fuser Error > 920.06 Service Fuser Error

920.06 Service Fuser Error

Contents

Use of the Codes" on page 2-17 Indicates that the fuser is below standby temperature when the printer is idle. To check for any stuck sheets of paper in the fuser unit: Locate the rear door and open it. If so, how do I test it or take it out?Thanks,Michael - mlucas 0 I have found a common cause of this error is the fused link on the blue cable there are 4 components making up this circuit #2 lamp holders a thermal fuse and the bulb it self. http://permamatrix.net/fuser-error/hp-cp3505-fuser.html

replace the fuser and your back up and running Oct 06, 2009 | Lexmark Optra T610 Laser Printer 1 Answer "922 SERVICE FUSER ERROR" 920, 921, or 922 Fuser Error: The Got it, continue to print 2012-2016 ManualsLib.com About Us About ManualsLib Privacy Policy F.A.Q. If this does not clear up the fuser error, the problem may be in one of the following: the fuser cover assembly the engine board the DC fuser cable the fuser The fuser would be the connector with the largest guage wires going to it.

920.06 Service Fuser Error

this is the heat lamp circuit. I would like to keep this printer if it is economical to do so. They think it might be too costly considering the age, but I would like to give it a try. The fuser is not warming up replace fuser.

Cheers, mole Respond to this 0 Same as lexmark codes:http://www.fixyourownprinter.com/lcodes.htmlI would check the continuity of the heater lamp inside the fuser. Remove the screws and push in the holding clips and the assembly should drop and the fan will be on the left. Restore password × Upload manual upload from disk upload from url Thank you for your help! Lexmark Fuser Replacement Look into the printer from the front.

Thanks J Prev12Next » Not finding what you are looking for? 924.01 Service Fuser Error percentage wise for this arching causing this failure is really close to 99.5% of the time. If this isthe first time you have seen the error, turn the printer off. http://www.verycomputer.com/14_e989e263bc57fc42_1.htm Feb 23, 2012 | Lexmark T630 Laser Printer 1 Answer Marca error 922 service fuser lexmark t520 922 Fuser Error messages indicate that the fuser unit failed to reach the standby

Where is this located and how can I test it?Any other suggestions on what to try next?Thanks,Michael Respond to this 0 It's a board on the right side of the printer. 922.02 Service Fuser Error Ask Anonymously Popular Questions 1 Answer How do I reset the IBM Infoprint 1532 Laser... 5 Answers Olivetti PR2E Passbook Printer IBM Proprinter II Matrix 2 Answers Driver IBM printer 4610 Answer questions, earn points and help others Answer questions Manuals & User Guides PDF Manual . If this does not help or if this error appears every time the printer is powered on, you will probably need service on the machine.

924.01 Service Fuser Error

Go to the Check" on page (Fuser) Sub Error Codes" on page 2-17 diagnose fuser failure. http://support.lexmark.com/index?page=content&segment=SUPPORT&locale=en&userlocale=EN&id=SO5058&productCode=LEXMARK_T656 Use of the "Base Printer 2-63. 920.06 Service Fuser Error Is there a recommended troubleshooting procedure for this error? Service Fuser Error Lexmark Printer If the printer has not recently had its fuser replaced, plug the printer directly into a wall outlet.

Where do I get replacement parts for this? have a peek at these guys Depending on how old your printer is, the fuser could need either rebuilt or replaced. If this is the first time you have seen the error, turn the printer off and on. I've also checked the connectors to the power supply and the ribbon cables.There is some talk about a low voltage power supply. Lexmark X654de Service Fuser Error

Tip: The max point reward for answering a question is 15. 0 characters Video Photos Link Replacement Parts Add Upload Upload × × Draw a box over the problem!! If I remember correctly you can see the fan when the top cover is up and you can even turn the round metal shaft by the side. Since three days when I switch it in I receive the following error message with three bips Error 922 Fuser Error. check over here Make sure the printer is plugged straight to the wall and not through a surge device or power strip.

The rear door opens and dropsdown towards you. 122.02 Service Fuser Error If this isthe first time you have seen the error, turn the printer off. Good Luck.

Mayor: An expert whose answer got voted for 2 times.

Question about IBM Printers & Copiers 1 Answer Marca error 922 service fuser ...922 service fuser lexmark t520 922 Fuser Error messages indicate that the fuser unit failed to reach the btw, I have never changed the printer toner since I own the printer. Back to Service Error Code List Source: Lexmark KnowledgeBase Home Page Technical Resources Lexmark Error Codes HP Error Codes Tech Support Blog HP Drivers Lexmark Drivers Terms & Conditions Product 924.01 Service Fuser Error Dell Keep in mind that there is no need to have the printer connected to a computer during testing for a fuser error as any pages to test the functionality of the

Question about IBM Printers & Copiers 1 Answer Dell laser printer m5200: 922 service fuser error dell laser printer m5200: 922 service fuser error how to solve this error? Did you mean? This gives the printer's engine board a chance to reset. http://permamatrix.net/fuser-error/hp-3600-fuser.html Use may help "Fan Service 2-3 Previous page Next page 1...262728293031323334 Related Manuals for IBM Infoprint 1130 Printer IBM INFOPRINT 1116 User Manual Ibm printer user manual (120 pages) Printer

Depending on how old your printer is, the fuser could need either rebuilt ... Personally, I never got a Lexmark printer to work doing this, but this is in the manual. Go to the Check" on page (Fuser) Sub Error Codes" on page 2-17 diagnose fuser failure. 1. Look into the back of the printer.

Service Fuser Error appears when the fuser does not warm to the required temperature. Is this an easy problem to fix? by Spose on Apr 3, 2006 at 7:07pm Add comment Please sign in to comment 0 Hi Spose,Thank you for your message. most likely the bulb in the fuser has gone out.

View Most Popular Infoprint 1120 Laser Printer Printers & Copiers Related Question 922 SERVICE FUSER ERROR Lexmark T630 Laser Printer Open Questions: 0 Answers printer is showing error 954 service nvram Next remove two screws which hold the redrive assembly. Problem with this is I did not have a fan that fit so I mounted a fan on the outside to suck the hot air out and it actually worked for Leave the printer off for at least 10 seconds before turning it back on.

Edit Close Save changes Attachments: Added items Uploading: 0% my-video-file.mp4 Complete.