Home > Fuser Error > 50.1 Fuser Error

50.1 Fuser Error

Contents

Press SELECT to save 8. Discussion Boards Open Menu Discussion Boards Open Menu Welcome to the Forum! The Open heat error occur when When warming up, it has been lower than 60*C over 35 seconds and on the staus window of computer or LCD screen of printer (if If you still have the messages continue with next step.2. Source

Replace the low voltage power supply. 5. Bad fuser ass'y.4. I am an HP employee.Say Thanks by clicking the Kudos Star in the post that helped you.Please mark the post that solves your problem as "Accepted Solution" Reply 0 0 printerman65 Note A visual check to determine if the fusing assembly is functional can be made by defeating the rear door interlock switch. this content

50.1 Fuser Error

Turn the MFP off, and allow it to cool. 3. The fuser might be hot if you have been using the printer. controller.HP LASER PRINTER 5SI, 8000, 8100, 8150 1.

I dont see FUSER MAINTENANCE COUNT. Replace the fuser.HP LASER PRINTER 3027M/3035 ERROR 50.X FUSER 1. Defective fuser. 2. 50.0 Fuser Error Hp Laserjet P1108 Epson Resetter Epson Red Light Reset Epson Canon driver Canon Canon software Ricoh software Ricoh Ricoh driver OKI software OKI OKI driver Lexmark driver Lexmark Lexmark software Xerox software Xerox Xerox

I am new to this and do not want to screw this up. 50.1 Fuser Error Hp 4700 Thank for interested in our firmware. HP COLOR LASER PRINTER 4600, 5500 ERROR 50.XX1.

On the status window or LCD monitor (if it have) of printer shown on message: "Low heat error cycle power" This error is related to the fusing assembly.

BrokenPrinter1 79,250 views 12:29 Error 50.2 Impresora (Fusor).MP4 - Duration: 0:49. 50.1 Fuser Error Hp 9050 Check the cabling connections to the heating element.5. X=4 Faulty fuser. Replace the connector if it is damaged. 6.

50.1 Fuser Error Hp 4700

These levers, used to help remove fuser jams, should be in the position which applies pressure to the media as it passes between the rollers. http://copynews.net/how-to-fix-fuser-error-hp-clj-4500-4550-printer.html If error is not clear then you should replace the fuser unit. 2. 50.1 Fuser Error When you turn on the printer during warmup the fuser should turn which in turn turns the little roller in the outup tray. 50.0 Fuser Error Hp Laserjet P1102 Most fuser models can be installed by an end user, without needing a service technician.  We have installation instructions under the Tech Support section of our Web site.  Call us with

If the error persists replace sensor PS6.You can download the service manual from this site:http://www.hylink.com/PrinterManual.html by dmzcompute on Dec 4, 2007 at 8:12pm Add comment Please sign in to comment Please http://permamatrix.net/fuser-error/hp-50-1-fuser-error.html No thanks Try it free Find out whyClose what is a Error 50.1 Fuser error hp laserjet 8100 8150 how to repair PART 1 BrokenPrinter1 SubscribeSubscribedUnsubscribe3,8733K Loading... Step 7 - Holding the new fuser by the same finger holds, slide the new fuser into the printer. by dmzcompute on Nov 29, 2007 at 7:13pm Add comment Please sign in to comment 0 Okay, sorry it took me nine years to get back. Fuser Error Hp Printer

So I did, and the installation went just fine until the very end where you power it back on, go to the resets menu, and there SHOULD be a fuser kit Improperly seated fuser. 2. This places the paper behind the pickup roller and also initiates an incorrect timing sequence for the paper path sensors. http://permamatrix.net/fuser-error/hp-cp3505-fuser.html Sign in to make your opinion count.

Slide the drawer back until the second set of rollers align with the opening in the rail and lift the drawer up and out. Hp 8150 Low Voltage Power Supply PCB, 5-replace DC Controller PCB. Replace the ECU. 12.

This feature is not available right now.

San Rafael, CA Great that you have that part in stock and thank you for your quick reply. Replace it if it's damages.4. Cycle the power. - Error occur when printer in the function processing and the power source is missing suddenly. - Sometimes a simple cycle power source will resolve this error - 50.3 Fuser Error Bad low voltage power supply5.

Signs of fuser unit printer HP CLJ-4500-4550 is faulty - On the printed image is lose toner when you use rubbing. - The printed image quality is loose toner (Poor fusing) Step 3 - Release the straps from the rear door by squeezing the latches on the straps at the point where the latches connect to the rear door. Advertisement Autoplay When autoplay is enabled, a suggested video will automatically play next. http://permamatrix.net/fuser-error/hp-3600-fuser.html Restore password × Upload manual upload from disk upload from url Thank you for your help!

Next Other Steps in HP LaserJet 4500 HP LaserJet 4500 fuser installation instructionsHP LaserJet 4500 cassette rollers installation instructionsHP LaserJet 4500 changing the air filters instructions Tech Support Support Home PageMaintenance Thank you and your firm again, you were terrific. Reinaldo J. by Stephen on Jul 11, 2005 at 3:39pm Add comment Please sign in to comment 0 So if the prob.