Home > Error Codes > Hp Laserjet 5100 Error Codes

Hp Laserjet 5100 Error Codes

Contents

Figure 43: Remove protective tape CAUTION: Do not touch the copper-colored contacts or the ink nozzles. Is the software set for the size you're using? If the issue persists, continue to the next solution. The self-test report prints. http://permamatrix.net/error-codes/hp-laserjet-600-m602-error-codes.html

Plug the printer into a wall outlet and see if this resolves the problem. 3. If it's broken, you will need to replace the sensor flag. Step two: Identify cartridges on the diagnostic page Use the sample diagnostic page below to identify the problem cartridge. Error 22 Error/ I/O Config Error/ Par I/O Error/MIO Error 22 EIO X BUFFER OVERFLOW The EIO card in slot X has overflowed it's buffer and data loss will occur 22 http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-c01386384

Hp Laserjet 5100 Error Codes

With the product turned on, disconnect the power cord from the rear of the product. Reconnect the power cord to the rear of the product. Close the top cover. May need to reload your PostScript print driver file.

It can also be caused by a defective DC controller. Also on the 4V/4MV check the door open sensor (PS402) on the terminal board located under the transfer roller. Replace this as an assembly. If the problem persists, contact your HP representative and arrange an on-site visit; have the message and the system error code ready with you to quote.

Press and hold the Power button. May be feed problem. As you can see we are not just another computer-products mega-website! http://h20564.www2.hp.com/hpsc/doc/public/display?docId=c00013363 XX20 Recover The printhead is losing its capability to produce the best image quality consistently.

The Devices window opens. Replace the laser/scanner. 53.XY.ZZ PRINTER ERROR There is a memory error with an accessory. Step four: Make sure that the carriage can move freely Press the Power button () to turn on the product. Disconnect the power cord from the rear of the product.

Hp Designjet 5500 Error Codes

Check I/O Cable, it could be the wrong cable or damaged. http://fixyourownprinter.com/posts/47873 If the issue persists, continue with the next solution. Hp Laserjet 5100 Error Codes and may not be used without advance written permission of PrinterTechs.com, Inc. Add memory or simplify the print job.

Contacting HP for service in all countries/regions except Asia Pacific. this contact form Disconnect the power cord from the rear of the product. Step two: Insert a replacement cartridge Open the top cover. Error 57 6P/5P/5 Main motor problem, check gear train for binding.

Check the printer’s configuration. 3. Figure 41: Raise the cartridge latches Slide the cartridge out of its slot, and then pull it towards you to remove it. Press and hold the Power button (), and then press the Print Cancel button (). have a peek here ERROR 40 Make sure computer and printer are set to the same baud rates.

Any help here would be appreciated too. Plug the power cord back into the wall outlet. Turn the printer off and then on. 3.

The product could not be added to your profile at this time.

Figure 38: Diagnostic page 1 - Printed by the right cartridge 2 - Printed by the left cartridge NOTE: If printing in reserve mode (one cartridge is removed), the diagnostic page All rights reserved. Select Yes to replace your cartridge with a genuine HP 705 cartridge, No to continue. 8X09 Supply Ink Level ? If the product does not turn on by itself, press the Power button () to turn it on.

Solution five: Service the printer If you have completed all the solutions listed above and are still experiencing a problem, continue to the Service the printer section at the end of Press the cloth against the rollers and rotate them upward with your fingers. Try to print. Check This Out Issue: The Print Cartridge light is blinking In this error condition, the following light pattern displays on the control panel: Print Cartridge status light: Blinking Resume light: Off Print Quality icon

On the IIP/IIIP this can be caused by a defective toner cartridge, defective cooling fan, PS4 or PS5 sensors. If these steps resolved the issue, and the test page prints, there is no need to continue troubleshooting. Solution three: Make sure that the cartridges are inserted correctly Improper placement or incorrect installation of the cartridges might cause the carriage stall error. Ensure that all the printhead cleaners installed are genuine HP 705.

Troubleshoot a problem Software and drivers (24) Windows (12) Macintosh (11) Other (Unix, Linux, Novell, etc.) (1) Installation and configuration issues (8) Printing (2) Windows (5) Network and wireless (1) Network Repeat these steps to insert the other cartridge. Figure 35: Do not touch the contacts or the ink nozzles Repeat the previous steps to remove the other cartridge. Defective MIO Card - Replace card Defective Formatter Card - Replace card Back back to top How did we do?

Sign-in Register Site help Skip to ContentSkip to FooterLaptops & tablets Business Premium Gaming Standard laptops Workstations Convertibles & detachables Tablets 3-in-1 Desktops Business Immersive Gaming Towers Workstations All-in-ones 3-in-1 Printers First perform the action indicated in the message. Pro Slate 12) OR Browse all HP products Please wait while we process your request.