Hp Laserjet 500 Mfp M525 Error Codes
Anyone have any idea what it means? Verify that the correct revision level of memory is installed in the printer. 53 Error Unit 153 Error Unit 1IIP, IIP+, IIIPAn error was detected on the optional memory board in Try with SIMMs or font cartridge removed to be sure error clears. 2. Error 30 PS Error 16 ALL PRINTERS This is an unexpected PostScript firmware error. http://permamatrix.net/error-codes/hp-laserjet-600-m602-error-codes.html
Verify accessory connection. 57.X PRINTER ERROR A fan failure was detected. Replace the formatter and/or firmware DIMM. 4. I usually remove them and reseat. Look for bits of paper lodged in the path particularly around the sensors. 4L/4P printers can have paper stuck in the pickup area which is accessed by removing the screw over page
Hp Laserjet 500 Mfp M525 Error Codes
Also try printing from a different application. This type of error can be caused by invalid print commands, corrupt data, or invalid operations. Defective laser scanner assembly. 4. This notice is included in its entirety at the beginning. 2.
You may have a worn pickup roller. The system returned: (22) Invalid argument The remote host or network may be down. If X=0, the slot with the defective SIMM could not be determined. Hp Warranty Check Replace the D.C.
If message persists, verify with the cartridge manufacturer the installed cartridge was designed for use with that model printer. Rm1-6322 All control panel settings return to factory default and the OO Ready message will read 68 Ready/Service until serviced. 69 Service II, IID, III, IIIDIndicates an optional I/O interface error. Bad or dirty cartridge contacts. This can generally get you 100 or so more pages.
HP LASER PRINTERS 3SI, 4SI 1. Hp Support On the 4P/5P printers, the top cover is open or no toner cartridge is installed. If the error is still present, switch off the printer and remove the SIMM board or type cartridge. Also, can I get some instructions on putting in the rollers.
Sometimes you can clean a pickup roller and get a little more life miles out of them but when you start to get jams with a smudge on the top middle http://www.printertechs.com/printer-troubleshooting/hp-error-codes/195-numeric-error-codes-50-59-hp-laserjet The printer has found a problem on the optional interface card. Hp Laserjet 500 Mfp M525 Error Codes To be honest 95\% of the time it is the laser/scanner motor wich is defective and the other times it is the dc controller. Hp Laserjet 600 M602 Error Codes Instead, please contact HP Customer Care Support, who could help and assist you in better ways.RegardsSohail Arshad Reply 0 0 davidzuts Regents Professor Posts: 4,701 Member Since: 01-17-2009 Message 7 of
If the message appears, consult service (for example, the problem is in the base printer memory or SIMM socket.) 64 Service4, 4M, 4Plus, 4Mplus, 4P, 4MPThe printer identified an internal service Check This Out Defective wiring harness from the scanner to the dc controller. 4. HP LASER PRINTERS 5000, 5100 1. The printer will still print, but will only be able to use the memory installed below the SIMM in question. Hp Printer Error Codes List
A laser beam error has occurred. 2. No color on the print job.HP COLOR LASER PRINTER 4600, 5500 ERROR 51.XK, 51.XC, 51.XM, 51.XY1. This error can also be software related. http://permamatrix.net/error-codes/hp-laserjet-5100-error-codes.html P/N RG1-0908-000CN.
If the problem persists, the cartridge or the printer may need repair. 72 ServiceIIISi, 4Si, 4Si MXA font cartridge was removed while the printer was trying to access it. We got it this morning and I have it installed. If the error persists, replace the laser scanner assembly.HP LASER PRINTERS 4200, 4300, 4250, 4350 ERROR 51.XX1.
Cuts or kinks in fiber optic cable. 4.
This board takes the input from the two sensors and provides info to the DC controller. If the error persists, consult service. 81 Service XXXX4, 4M, 4Plus, 4Mplus printersThe printer detected a problem with an internal controller. Error 57 6P/5P/5 Main motor problem, check gear train for binding. Defective High Voltage power supply or on the LJ II/III the DC controller to High Voltage power supply can be defective.
The only time one of those connections is bad is when work is done on the printer and the tech is not careful when reassembling. We sell maintenance kits, fuser, repair parts and supplies.