Home > Error Codes > Hot Tub Error Codes

Hot Tub Error Codes


System will restart when temp. The system returned: (22) Invalid argument The remote host or network may be down. SEoP = Sensor open or disconnected. Heater disabled but the spa is operational. navigate here

Inspect these first:• Check slice or ball valves. COL / 05 Cool Water Condition, Temp falls 20 degrees below set temp. What is the minimum and maximum temperature setting for the VS-Series Spa Controllers? 108. Support: GFCI Immediately trips.

Hot Tub Error Codes

Spa has shut down. This is a normal spa function; no further action is necessary.When either sensor reads below 40 degrees F., the system provides freeze protection. th2/current temperature = On startup indicates temperature probe problem. Heater is shut down, but other spa functions run normally.

Support: The Glued Plumbing Configuration will not align up to the Pump and Heater on a Spa Pack. 68. Low speed pump (and air blower if so equipped) will activate to assist in lowering temperature. --- = "Watchdog". Below we have listed the most common error codes, your spa manufacture may havere-brandedone of these controls. Vita Spa Error Codes If water temperature drops 20ºF below set temperature, low speed pump and heater activates to bring temperature within 15º of set temperature.ICE = Freeze condition. 55ºF detected.

Press and hold the Light key for 5 seconds. For more information regarding Balboa tech support click here Gecko Spa Side Error Codes FLO : Pressure switch failure, switch open FLC : Pressure switch failure, switch closed Prr : Temp No action is necessary.PnL = Communication between the panel and circuit board is faulty.---- = "Watchdog" (spa is deactivated) A problem has been detected.Sn1 = Open sensor (heater is deactivated) or FL = Flow.

drops. Hydroquip Spa Systems The low speed pump or circ pump will operate continuously until the temperature rises above 45° F. This indicates a persistent flow problem The heater is shut down while all other spa functions continue to run normally. The Spa or Hot Tub Panel Displays: Sn, SnS This indicates that the sensors are out of balance.If alternating with temperature, it may just be a temporary condition.

Balboa Hot Tub Error Codes

drops.HL = High limit switch tripped. http://www.spapartsshop.com/spasideandtopsideerrorcodes.aspx During this cycle all other functions of the unit (except the alarms) are disabled. Hot Tub Error Codes The light will automatically turn itself off after 2 hours. Hydroquip Spa Troubleshooting Spa has shut down.

dr = Inadequate water detected in heater. http://permamatrix.net/error-codes/ibm-svc-error-codes.html HFL = Substantial difference between temperature sensors detected. All rights reserved. Support: Hi-Limit Sensor Installation on a SpaGuts CS-Series Electronic Controller. 128. Hydroquip Hq6000

PayPal Payment Information 146. BUT, you helped me figure out what part I needed for my hot tub and I really appreciated that:) I will highly recommend your website to anyone needing parts/and or service!!" Support: Blower is tripping the GFCI (SpaGuts Brand). 31. his comment is here Then re-start the hot tub, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off.

Support: SpaGuts Inline Bath Heater Installation 114. Marquis Spa Error Codes Will 208V supply be OK for a Spa Pack rated at 240V? 150. COL = Cool condition.

What information do I need to get the correct wiring diagram for the SpaGuts brand Controller? 71.

Pump and heater will be turned on for one minute. Heater is deactivated. Spa Builders Spa Side Error Codes Sn1 = Nonfunctional high temperature sensor. Gecko Spa Pack Error Codes Spa is over heating. 73.

If itwill not reset, check for clogged filters. FL1 = Water flow problem, inhibited or pressure switch malfunction. Spacare.com 888-772-9887 Technical Assistance 405-622-4950 0 Item(s) | Total: $0 Home Shop SpaCare.com Spa Part Index Circuit Board Repair Spa Covers Spa & Hot Tub Covers Spa Cover Lifts weblink Light Key The Light key is used to turn light on or off.

Support: I ordered the wrong plumbing configuration on the spa pack. 17. Entire system is disabled. ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://www.spadepot.com/spa-error-codes.htm Connection to failed. The maintained temperature will default to 95ºF.

IMPORTANT NOTES: (1) If a program change is not made within 5 seconds, the system will default back to the monitoring mode. (2) While programming, the Pump and Light features may Support: Wiring information for the (15-350-4015) Exec-48 1.5HP 110V WaterWay pump, 2.5" Intake, 342061A-13 102. Support: Temperature reading in Fahrenheit or Celsius on a Balboa 54115 Circuit Board, 54114 Balboa System 88. Support: Balboa topside displaying ---F 59.

The first press of the Light key will turn the light on. Support: New pump making vibrating or buzzing noises on low and/or high speed, but runs fine. 87. Support: Replacement thermostat does not work 107. How do I clock the pump on my motor? 35.

The cycles will repeat every 24, 12, or 8 hours within a 24 hour period, Starting from the time programmed. Support: Wiring information for the (15-350-2293) Spa-Flo 2.0HP 220V SD Waterway Pump, 342102A-0Z. 84. The Air Pump will automatically turn itself off after 20 minutes. Home Shopping Cart Bath Tub Pumps & Heaters Spa Parts Major Packs Controllers Heaters Pumps & Motors Blowers Ozonators Filter Systems Balboa Brand Parts Hydro Quip Brand Parts Spa Parts Minor

Support: FLO or 3 blinking dots error code. (Electronic Only) 4. The system returned: (22) Invalid argument The remote host or network may be down. Fill out my Wufoo form!